How much does siding cost in Hammond?

Estimated at $3 to $18 a square foot fitted. Standard vinyl sits at the bottom of that, insulated vinyl and engineered wood in the middle, fibre cement and metal at the top. A whole home job normally runs five to ten days on site.

Which siding suits this climate?

Fibre cement and engineered wood both handle sustained damp and heat well, with fibre cement the more stable and the heavier of the two. Vinyl is the cheapest to fit and the least tolerant of long term heat. There is no single right answer, which is why the table above gives behaviour rather than a winner.

What happens if you find rot behind the old siding?

We stop, photograph it, price the repair as its own line and get it agreed before carrying on. It is common on an older inland Louisiana house and it is far better handled as a named contingency on the quote than as a surprise on the day.

Do you replace the housewrap and flashing?

Where they need it, yes, and it is quoted rather than assumed. Cladding sheds water but does not seal a wall, so the wrap and the flashing at every opening are what actually keep the wall dry. A quote that ignores them is pricing half the job.

Do the City overlays apply to a siding change?

The Hammond building permit application names a Historic District overlay and a Downtown Development District overlay among its overlay options. Whether either applies to your address, and what review a siding change needs if it does, is a question for the City of Hammond Building Department on (985) 277-5655 rather than one to read off the form. We flag it during the measure so the answer is confirmed before anything is ordered.

Do I need a permit to replace siding?

Normally not for a like for like replacement that touches no structure. Structural repair found behind the cladding, or any change to openings, can require one, and we confirm the position with the office that covers your address once the wall has been seen. Inside the Hammond city limits that is the City Building Department at 219 E Robert Street; outside them it is Tangipahoa Parish.

Is fibre cement worth the extra over vinyl?

It depends on how long you intend to own the house and what the wall behind it is like. Fibre cement is more stable in this climate and costs more to fit; vinyl is cheaper and easier to replace. We will price both against the same wall so the comparison is real.

How long does a whole home take?

Five to ten days on site for a typical house, depending on elevations, access, the amount of trim work and what the wall turns out to need once the old cladding is off.

Home/Service Areas/Louisiana/Hammond/Siding Installation

Siding Installation in Hammond, LA

Big Easy Roofing fits siding across Hammond and Tangipahoa Parish. The cladding is the visible half of a siding job and the least of what decides whether it lasts fifteen years in this climate; the wall behind it and the detail at every opening are the other half, and they get looked at before anything goes back on.

Get Your Free Siding Quote Call (504) 800-8196

Service

City

$3 to $18 /sq ftEstimated installed

5 to 10 daysTypical whole home

Overlays namedOn the City permit form

Drainage planeChecked before cladding

Hammond siding installation at a glance

Siding is estimated at $3 to $18 a square foot fitted, which is a wide band because the material choice runs from standard vinyl at the bottom to fibre cement and metal cladding at the top. A whole home job normally runs five to ten days on site.

Estimated installed cost

$3 to $18 /sq ft

Vinyl at the bottom of the band, fibre cement and engineered wood at the top. Call Big Easy Roofing on (504) 800-8196 and we will measure the elevations and quote the material you actually want.

Which office covers you

City or parish, by boundary

A like for like siding replacement that touches no structure normally needs no permit. Structural repair found behind the cladding can change that, and the office that reviews it is the City of Hammond Building Department at 219 E Robert Street inside the city limits, or Tangipahoa Parish outside them.

Overlays named on the permit form

Historic District and DDD

The City of Hammond building permit application names five overlays: Thomas/Morris, Hyer-Cate, Iowa Addition, the Historic District and the Downtown Development District. Whether any of them applies to your address, and what review a specific change needs, is a question for the City rather than something to read off the form alone.

Typical duration

5 to 10 days

A whole home, depending on elevations, access, how much trim work there is and what the wall behind the old cladding turns out to need.

Materials fitted

5 systems

Fibre cement, engineered wood, insulated vinyl, standard vinyl and metal where the look suits. Each behaves differently in sustained damp and wind, which is set out in the table below.

Warranty

Workmanship plus product

Our workmanship warranty on the installation, alongside whatever the manufacturer offers on the product itself. The product terms are theirs, so we confirm what they require before starting.

Every figure on this page is an estimate, not a quote, and is subject to Big Easy Roofing sign off. Cost and timescale depend on size, pitch, access, weather, materials and whatever is found once work starts, so call Big Easy Roofing on (504) 800-8196 and we will come out and give you an estimate for your own roof.

Siding gets chosen on appearance and priced by the square foot, and both of those are reasonable. What decides whether it is still doing its job in fifteen years is neither. It is whether water that gets behind the cladding, which it always eventually does, has a way back out.

That is the drainage plane: the housewrap, the flashing at every opening, and the gap that lets a wall dry. In a climate this humid a wall that cannot dry will fail behind cladding that still looks new, and the cost of putting that right is far higher than the cost of detailing it properly the first time. So the wall gets opened and checked before anything goes back on, and anything found is priced as its own line rather than absorbed quietly.

How each material behaves in an inland Tangipahoa climate

The materials differ more here than they do in a dry state, because sustained humidity and storm bands moving up from the coast test them in ways a catalogue does not. The table gives the estimated installed cost and how each one actually behaves in this part of the parish, which sits inland but well inside hurricane reach.

Material	Estimated installed	How it behaves here	Worth knowing
Fibre cement	$8 to $14 /sq ft	Stable in damp and heat, does not feed insects	Heavy, so the wall and fixings matter. Cutting needs dust control
Engineered wood	$6 to $12 /sq ft	Lighter than fibre cement, warmer look	Depends entirely on the factory coating staying intact at cut edges
Insulated vinyl	$5 to $9 /sq ft	Better against heat than standard vinyl	The foam backing adds rigidity, which helps against wind
Standard vinyl	$3 to $7 /sq ft	Cheapest to fit, least tolerant of sustained heat	Can become brittle over time in this climate, so fixing detail matters
Metal cladding	$9 to $18 /sq ft	Sheds water well and takes wind	Fastener and coating choice decide how it ages in a humid inland climate

Estimated ranges, not quotes, and all of them assume a sound wall behind the cladding. Anything found once the old siding is off is priced as its own line and agreed before the crew carries on. Call (504) 800-8196 for a measured quote.

What sits behind the cladding and which office covers your address

Two questions decide a siding job here, and neither is which colour. What the wall behind the old cladding is doing, and whether the address sits inside one of the overlays the City names on its permit form. The colour is the easy part and the part you already know.

Cladding sheds water, it does not seal

The wall does the rest

No siding system is watertight and none is meant to be. Water gets behind it at openings and in wind driven rain, and the assembly behind is what carries it back out. That is the part that decides the life of the job.

Which matters more in sustained damp

Than in a dry climate

A wall that gets wet and dries is fine. A wall that gets wet and stays wet is not, and this climate supplies far more of the first condition than most. Housewrap laps, flashing at every opening and a drainage gap are what separate the two.

Overlay review can apply to exterior changes

Named on the City form

The City of Hammond permit application names a Historic District overlay and a Downtown Development District overlay among its overlay options. A siding change is exterior, so where an address sits inside one of those overlays the specific review path comes from the Building Department on (985) 277-5655, not from the form itself.

Outside the city limits

Tangipahoa Parish covers the rest

For an address in the unincorporated area, the Parish Permit Office on (985) 542-2117 is the office to ring instead. The Parish states it implemented the 2021 building codes and the 2020 NEC effective 1 January 2023.

Nothing here about the 2025 roofing rule

Different work entirely

La. R.S. 37:3737(I) covers roof construction and re roofing. Siding is neither, so it sits outside that regime altogether, and any roofer telling you otherwise has not read it.

What to ask any siding quote in this market

Ask what happens to the housewrap and the flashing, not just which cladding is going on. A quote that prices only the visible material is pricing half the job, and it is the half that does not decide whether the wall lasts.

Ask, too, what happens if rot is found once the old siding comes off. It is common on an older inland Louisiana house, it changes the price, and it belongs on the quote as a named contingency rather than as a conversation on the day.

Why the fixing detail matters more here than the material

Wind loading on a wall is highest at corners and openings, which is exactly where cladding is most often under fixed and where installers rush. Inland Tangipahoa still sits under storm bands moving up from the coast, so a material rated for high wind fitted at the wrong spacing is not rated for anything.

So the fastener type, the spacing and the detail at corners and around windows are worth more attention than the choice between two products that both look fine on a sample board.

Get Your FREE Quote Call (504) 800-8196

What shortens siding on a Tangipahoa house

Three things account for siding failing early in this part of Louisiana, and none of them is the cladding wearing out. They are all about water getting somewhere it cannot easily leave again, which is why the detail work at openings and edges matters more than the product choice.

Openings, where much of it starts

Windows and doors are holes in a wall made watertight by flashing rather than by cladding. Head flashing that is missing, short, or lapped the wrong way sends water into the wall instead of over it, and the cladding above looks perfect while it happens.

It is the first thing checked when the old siding comes off, and it is cheap to put right at that moment and expensive at any other.

Ground contact and splash at the bottom course

The bottom of a wall takes splash from every storm and can sit near soil and planting. Cladding held too near the ground wicks moisture upward and never dries properly, so failure starts at the bottom course and works up.

The fix is clearance and a proper starter detail rather than a different material, and it costs almost nothing to get right during an installation.

Cut edges that were never sealed

Fibre cement and engineered wood are protected by their factory coating, and every cut on site creates an edge that has none. Sealing those cut ends is a small, dull, easily skipped step, and skipping it is a preventable reason a good product ages badly.

It is invisible once the board is up, which is exactly why it is worth asking about before the work starts rather than after.

Big Easy Roofing Process

Three steps, and the wall gets looked at between the first and the second, because a siding quote written without seeing the wall is a quote for half the job.

A contractor measuring the elevation of a Hammond house for siding

Get Your FREE Quote Call Our Roofing Experts!

Measure and specify

Elevations measured, material and trim agreed, and the existing cladding checked at openings and at the bottom course for what it is likely to be hiding. Overlay position confirmed with the City where the address may sit inside a named overlay.

Strip, check and detail the wall

Old cladding off, the wall assembly inspected, housewrap and flashing put right, and anything structural found priced as its own line and agreed before we carry on.

Clad, trim and finish

New cladding fitted to the manufacturer detail with the fixing spacing the wind loading needs, trim and corners finished, cut edges sealed, and the site left clear. Call (504) 800-8196 to book the measure.

Everything else we do in Hammond

The rest of the Big Easy Roofing services available in Hammond, each with its own page, scope and written estimate. Siding work often uncovers gutter or fascia issues at the same elevation, and those are priced as their own lines.

Filter by service type: