How much does a gutter repair cost in Kenner?

A single defect repair is typically estimated between $150 and $600, priced on the defect rather than the length of the run. A blocked downspout sits at the bottom of that and a wind damaged downspout near the top. Fascia rot behind the gutter is the exception at $300 to $700, because it is joinery as well as gutter work. A visit fixing several defects at once is typically estimated between $600 and $1,800 as one bundled scope.

Why does my gutter overflow when I only had it cleaned?

Because a clean gutter still has a fixed capacity. It is set by the size of the profile, the fall and the number of downspouts against the roof area draining into it. Coastal Louisiana takes rainfall in short heavy bursts, so a run that would cope in a drier market can be genuinely undersized here, and the NOAA Atlas 14 rainfall intensity at your specific address is a measure of how hard the rain can fall.

Should I repair or replace the run?

Under three defects on an otherwise sound run is normally worth repairing. Three or more on the same run usually means the sealant, the coil stock or the fascia fixing behind it has reached the end of its life, and each repair tends to buy months rather than years. We price the replacement against the repairs on the same visit so it is your call. Sizing for a replacement is set on the gutter installation page rather than repeated here.

What happens if you find rot behind the gutter?

It is a common find, because overflow soaks the fascia the gutter is fixed to. We stop, itemise the fascia work as its own line on an amended scope, and get it signed before carrying on. It is not added to the bill without your agreement.

How long does a gutter repair take?

A single defect repair typically takes one to two hours in a single visit, normally the same week as the diagnosis. Fascia rot behind a run is the exception at two to four hours, and a whole run replacement is about half a day.

Will gutter guards stop it happening again?

They help where the problem is genuinely debris at the outlet, and on a house that catches wind blown leaves that is often what the debris load points to. They do nothing at all if the run is undersized for the roof feeding it, which is why we check the capacity first. Fitting guards to a gutter that is too small just hides the reason it overflows.

Where does the cleared debris go?

It leaves with us. The City of Kenner states it has ordinances prohibiting the dumping of any material in its drainage system (Code of Ordinances Section 9 1/2-6), and a catch basin is part of that system, so on our visits leaves and grit cleared from a run are bagged and removed rather than swept to the kerb. Public Works on (504) 468-7515 is the office to call if a routing question comes up.

Can you match my existing gutter?

Usually. Aluminium in the common profiles and colours is straightforward, and a seamless run is formed on site to the exact length so there are no mid run joints to fail later. Older steel, copper and discontinued profiles are assessed on the visit, and we will say plainly if an exact match is not possible before starting rather than after.

Home/Service Areas/Louisiana/Kenner/Gutter Repair

Gutter Repair in Kenner, LA

Big Easy Roofing repairs gutters and downspouts across Kenner and east bank Jefferson Parish, priced per defect rather than per foot. Louisiana rain arrives in short heavy bursts, and in Kenner where much of the ground sits at or below sea level, a run that overflows onto the ground moves more debris toward the catch basin than an equivalent run in a well drained suburb.

Get Your Free Gutter Quote Call (504) 800-8196

Service

City

$150 to $600Estimated per defect

1 visitTypical gutter repair

No permitRepair, not construction

Bagged and removedCleared debris leaves with us

Kenner gutter repair at a glance

A gutter repair is a scoped fix for a single defect: a sagging run re hung, a leaking seam re sealed, a blocked downspout cleared, or a torn end cap replaced. A single defect is estimated at $150 to $600 and normally finishes in one visit. Cleared debris leaves with us rather than being swept to the drain.

Estimated per defect

$150 to $600

A single defect repair on a residential gutter, priced after an on site diagnosis. Call Big Easy Roofing on (504) 800-8196 and we will walk every run and photograph each defect before anything is quoted.

Multi defect visit

$600 to $1,800

Two or more defects on the same visit, such as several sagging runs, a few failed seams and a torn end cap, priced as one bundled scope rather than as separate call outs.

Which office covers you

City of Kenner, by boundary

A gutter repair is not a roof covering change, so the state reroof rule that came in during 2025 does not reach it and no permit is pulled for repair work. Where a visit grows into roof work we confirm the position with the City of Kenner Inspection and Code Enforcement Department at 1926 18th Street on (504) 468-4064 before continuing.

Repair or replace

Under 3 defects

Under three defects on an otherwise sound run usually means a repair. Three or more on the same run usually means the sealant, the coil stock or the fascia fixing behind it is at the end of its life, and replacing that run is the better value. Sizing decisions for a replacement are set on the gutter installation page rather than repeated here.

Where the cleared debris goes

Bagged and removed

Leaves, granules and grit cleared from valleys and gutters are bagged and removed from site. The City of Kenner states it has ordinances prohibiting the dumping of any material in its drainage system (Code of Ordinances Section 9 1/2-6), and a catch basin is part of that system. See roof maintenance for the wider Kenner drainage framing.

Warranty

1 yr workmanship

One year workmanship warranty on the repair we carry out, whether that is the sealant, the hangers, the re seat on the fascia or a replacement run.

Every figure on this page is an estimate, not a quote, and is subject to Big Easy Roofing sign off. Cost and timescale depend on size, pitch, access, weather, materials and whatever is found once work starts, so call Big Easy Roofing on (504) 800-8196 and we will come out and give you an estimate for your own roof.

A gutter usually gets a call when water is doing something it should not. It sheets over the front edge in the middle of a run, it drips down the fascia and stains the wall, it pools at the base of a downspout, or a section has visibly dropped away from the roof line. Each of those has a different cause and a different fix, which is why the diagnosis comes before the price rather than after it. Every figure on this page is an estimate, not a quote, and is subject to Big Easy Roofing sign off.

The one worth understanding before you call anyone is overflow, because the obvious cause is not always the real one. The standard answer is that the gutter is blocked, and sometimes it is. But a gutter has a fixed capacity, set by its size, its fall and the number of downspouts against the area of roof draining into it, and heavy bursts are what test that capacity. A clean gutter that still overflows in a heavy storm is not dirty. The reasons are that it is undersized for the roof feeding it, has too few outlets, or has lost its fall, and which one it is can be checked.

The Kenner detail on top of that is where the overflowing water ends up. kenner.la.us/191 states that most of Jefferson Parish and the City of Kenner lies at or below sea level and that rain is the most common source of flood water in the City. A gutter that spills onto the ground moves leaves and grit toward the catch basin, which is the same shape of problem the City ordinance (Section 9 1/2-6) addresses when it prohibits dumping material in the drainage system. So the sensible fix is to solve the reason it overflows rather than to book a second clean, and cleared debris leaves with us rather than being swept toward the drain.

Common gutter defects and typical scope

Gutter repairs fall into seven classes. The table gives the typical scope, the estimated price band and how long each takes on site. Under three defects on one sound run is usually a repair. Three or more usually means replacing the run beats stacking fixes.

Defect class	What we do	Estimated price band	Visit length
Sagging run, one to three hangers	Re hang on new hidden hangers, re seat to the fascia	$150 to $350	1 to 2 hours
Leaking seam or corner	Clean the seam, re seal with butyl, re bed the corner joint	$150 to $300	1 to 2 hours
Blocked downspout	Clear the blockage, flush through, test the flow at the outlet	$150 to $250	1 hour
Torn end cap or missing splash block	Replace the end cap and re seal, or fit a new splash block	$150 to $300	1 hour
Wind damaged downspout	Re hang or replace the downspout section and secure it to the wall	$250 to $500	2 hours
Fascia rot behind the gutter	Take the section down, replace the rotten fascia, repaint, re hang	$300 to $700	2 to 4 hours
Whole run replacement	Strip the failed run, form new seamless aluminium on site, re hang	$600 to $1,800	Half a day

Estimated ranges, not quotes, and none of them includes a capacity upgrade such as a larger profile or an extra downspout, which is priced separately once the roof area is measured. Sizing decisions live on the gutter installation page rather than being repeated here. Call (504) 800-8196 and we will put the defect, the fix and the price in writing before anything starts.

Why a clean gutter still overflows and whether you need a permit

Two things decide most gutter repairs in this market. Why a run overflows when it was cleared only months ago, and whether the 2025 Louisiana roofing rule applies to gutter work at all. The short answers are capacity rather than dirt, and no, because a gutter is not a roof covering.

The Louisiana coast is a heavy rainfall market

A wet one

The National Weather Service normals put the New Orleans area at around 63.5 inches of rainfall a year, and the east bank sits inside that. Annual totals move around from year to year, but the number that decides whether a system copes is the rate the rain arrives at rather than the yearly sum.

Capacity is set per run

Atlas 14 at your address

Gutter and downspout capacity is worked out from the roof area draining into a run against the rainfall rate it is sized to carry. NOAA Atlas 14 publishes 100 year 60 minute rainfall intensity estimates for a specific set of coordinates. A Kenner-specific figure is not verified in the research on file here, so the calculation is run against the rate returned for your actual address rather than a borrowed number.

Which is why cleaning does not always fix it

Undersized, not dirty

If a run is too small for the roof feeding it, or has too few outlets, it will overflow whenever the rain is hard enough no matter how recently it was cleared. The fix is a larger profile, an extra downspout, or a corrected fall, and we will say which rather than booking you a second clean.

A gutter repair needs no permit

Not a covering change

The state rule that came in during 2025 covers roof construction and re roofing, and gutters are not a roof covering. A gutter repair sits outside it. If a visit turns into roof work we confirm the position with the City of Kenner Inspection and Code Enforcement Department on (504) 468-4064 before continuing.

A loaded run in wind is a fixings question, not a cleaning one

A gutter full of water already carries real weight, and wind driving that run puts more load on the fixings than a still storm of the same total rainfall does. That is why a run can be perfectly clear and still come away from the fascia after hard weather.

The tell after a hard weather event is a sagging run that did not sag before, or a length of gutter that has visibly moved on its fixings. That is not a cleaning problem, it is a fixings problem, and re hanging on a tighter spacing with the fascia checked behind is the honest fix rather than another clean.

Overflow, fascia rot and where the water ends up

The damage from an overflowing gutter is rarely the water you can see. Water that backs up behind the run reaches the fascia, which is the timber the gutter is screwed to. Wet fascia holds moisture against the roof edge, the hangers lose their grip, the run sags further, and it overflows more.

The Kenner detail on top of the loop is where the spilt water then goes. kenner.la.us/191 states that most of Jefferson Parish and the City lie at or below sea level and that rain is the most common source of flood water in the City. A run overflowing onto the kerb moves leaves and grit toward the catch basin, which is the same shape of problem the City ordinance (Section 9 1/2-6) addresses when it prohibits dumping material in the drainage system. A sagging run re hung early is a couple of hundred dollars and stops the loop before soffit and eave framing are involved.

Get Your FREE Quote Call (504) 800-8196

Why gutters fail on an east bank Kenner house

Three patterns come up in the repairs we quote on east bank Kenner houses. Heat and humidity working on sealed seams, wind pushing a fully loaded run at the fixings, and outlets that block faster than the gutter above them. Each has its own tell, its own fix and its own price band.

Seams giving way to heat cycling

A sectional gutter is watertight because of a bead of butyl or silicone at each lap joint. That bead expands and contracts every day of a Louisiana summer, and a sealed joint is a common place for a leak to start, at the joint rather than anywhere along the sheet.

The tell is a dark drip stain on the fascia directly under a joint, and a narrow wet patch on the wall below it during rain. One seam is a straight forward re seal. Several failing on the same run means the whole run is at that age, and a seamless replacement with no mid run joints at all is the fix that lasts.

Wind loaded runs pulling their fixings

A fully loaded gutter under a Gulf storm is heavy in itself, and wind blowing along the eave adds a horizontal load the fixings were not sized to hold on their own. The result is a run that lets go progressively rather than all at once: it moves on its hangers first, then it sags at the low point, then the water sheets over the front edge instead of running to the outlet.

The tell is a visible dip in a run that was straight last year, and water sheeting over the front rather than reaching the downspout. The repair is usually new hangers at a tighter spacing, once the fascia behind them has been checked, since a sag can come from rot or failed fixings rather than spacing alone.

Outlets that block, and where the debris then goes

The downspout outlet is the narrowest part of the whole system, so it can block while the gutter still looks clear from the ground. One blocked outlet is enough to flood a bed or a walkway in a single storm, and on a Kenner house where the ground next to the kerb slopes toward a catch basin, that overflow moves leaves and grit into a drain the City ordinance (Section 9 1/2-6) addresses when it prohibits dumping material in the drainage system.

The tell is water overflowing at the downspout end rather than in the middle. Clearing it is quick and cheap, and the cleared debris leaves with us rather than being swept into the street. If the blockage keeps happening, the honest answer is usually guards or a larger outlet rather than a standing appointment to clean it out.

Big Easy Roofing Process

Three steps and a free first visit. The diagnosis is per defect, so you can see what is being repaired and why before any number is agreed.

A roofer in a high visibility vest measuring a fascia and downspout run from a ladder

Get Your FREE Quote Call Our Roofing Experts!

Free on site diagnosis

An estimator walks every gutter run, finds every defect and photographs each one, and checks whether the run is actually big enough for the roof draining into it. You keep the photographs whether or not you use us.

Written quote, defect by defect

The scope names each defect, the fix, the materials, the warranty and the price. Where three or more defects sit on the same run, replacing that run is priced against the sum of the repairs so the sensible call is obvious rather than argued.

Repaired, usually within the week

A gutter repair is typically finished in one return visit inside a week. The cleared debris is bagged and removed from site. The written price stands unless something behind the run changes the scope, and then it is amended in writing and signed before the crew carries on. Call (504) 800-8196 to book the diagnosis.

Everything else we do in Kenner

The rest of the Big Easy Roofing services available in Kenner, each with its own page, crew and written scope. Because gutter overflow is a common cause of fascia rot behind the run, joinery work is often found on the same visit and priced beside the gutter fix.

Filter by service type: