Big Easy Roofing Logo
Claim Banner - Big Easy Roofing Big Easy Roofing roof replacement guarantee banner
Call Our Roofing Experts!(504) 800-8196
Home/Service Areas/Louisiana/St. Rose/Commercial Roof Leak Detection

Commercial Roof Leak Detection in St. Rose, LA

Big Easy Roofing traces commercial roof leaks across St. Rose and the east bank of St. Charles Parish. The covering on the roof helps decide the test, and a core cut can check a reading and show the layers at one spot.

Covering firstIt helps decide the test
Core cutChecks a reading at one spot
LayersSeen in the core
Written traceEntry point, cause, scope

St. Rose commercial roof leak detection at a glance

A leak trace starts with the covering. A single-ply roof can be tested electronically or by controlled flood where the system and a qualified assessment allow. Other coverings are usually read from the stain and details. A core cut can then record conditions and layers at one spot, which bear on the regional handout rule on two or more coverings.

Single-ply membranes

Electronic or controlled flood

Low-voltage scanning, high-voltage spark testing or a controlled flood test is chosen for the membrane and the structure. The manufacturer is checked first for electronic suitability.

Other coverings

Built-up, modified bitumen, metal, sloped

On built-up, modified bitumen and metal roofs the seams, laps, fasteners and details are read first. On sloped coverings the trace can go upslope from the stain, checking flashings, valleys, penetrations and edges, though water can also travel sideways.

The core cut

One spot, what it shows

A small section is removed so the layers can be seen at that spot, and, where there is insulation, a moisture reading gives an indication of moisture at that spot. Our practice is to patch it as soon as weather and access allow. It tells us about that location, and a roof can differ from one section to another.

The number of coverings matters to the regional handout

Two or more applications of coverings

The SCPDC roofing handout linked on the parish permits page says, for areas where wind design is required, that new roof coverings shall not be installed without first removing all existing layers where the roof has two or more applications of coverings.

What a trace aims to deliver

Likely entry point and scope

The scope says what the trace found, where, and what we recommend. Where a roof has taken in water, a moisture survey looks for wet insulation where the assembly includes it, because the extent can affect the scope.

What we will not interpret

Your insurance

Louisiana R.S. 37:2159.1 bars a roofing contractor from acting as a public adjuster or interpreting insurance policy coverage. The trace documents the roof.

This page addresses roofing on buildings other than one- and two-family dwellings. For a mixed use building, confirm with the parish which rules apply.

Commercial leak detection is scoped to the roof, the method and the access, so call Big Easy Roofing for a price on your St. Rose building.

Electronic leak detection against the controlled flood test

On a single-ply membrane, these methods are used to answer the same question, each with its own limits. The membrane type, the size of the area and an assessment of the structure and the drainage decide between them, and a core cut can check a result at one spot.

MethodHow it worksWhere it fitsWhere it does not
Low voltage scanningAn electrical method that looks for a conductive path associated with moisture at a breach, where the membrane and substrate suitWhere the membrane, the substrate and the manufacturer allowConductive membranes and foil facers
High voltage spark testingA wand over a dry membrane; a breach can register as a sparkWhere the membrane, the substrate and the manufacturer allow, often smaller areas and detailsAny membrane the manufacturer says it may damage, and flammable or combustible substrates
Controlled flood testWater dammed to a controlled depth, interior watched, after the drainage and the structure have been assessedA defined area where the structure, the drainage and the space below can take it, and the warranty allowsSpaces below that cannot take water, and some large areas
Built-up, modified bitumen, metal or sloped coveringsRead from the stain, the seams, flashings and penetrations, upslope on a sloped roofCoverings the membrane test methods often do not suit, or where the surface and deck decide itIt relies on the trace being read correctly, and a core can check the layers and moisture at one spot

Membrane suitability for electronic testing is checked against the manufacturer first, and on a warranted roof the warranty terms are checked before a destructive test.

The core cut and what the number of coverings means

A core cut records the layers and the moisture at one spot. The regional roofing handout states a rule that turns on whether a roof has two or more applications of coverings, so the layers are worth recording before a replacement or re-covering scope is written. What the rule means for your building is a question for the building official.

What the core shows

Layers, insulation, moisture

Any membrane and insulation the core passes through can be seen in the section and, where the core goes through to the deck, the deck and any earlier coverings it passes through. A core may not reach the deck, and one sample may not show every earlier covering. A moisture reading gives an indication of moisture in the insulation at that spot. Where the trace and the core agree, the finding is firmer than either alone, though the core speaks only for conditions at the spot where it was taken.

What the handout says

Two or more coverings

The handout says, for areas where wind design is required, that new roof coverings shall not be installed without first removing all existing layers where the roof has two or more applications of coverings, and that attaching a new covering to existing wood shake, slate, clay, cement or asbestos-cement tile is not allowed.

What the two stated sentences do not say

A single covering

For one existing covering that is not one of those shake or tile types the handout’s two sentences say nothing, and whether the layers in a core count as separate applications of coverings is a question to put to the building official, so we do not say a recover is allowed or barred. The commercial replacement page covers that decision, and the building official answers it for your roof.

Whether a repair needs a permit

For the parish to say

Whether a leak repair needs a permit is for St. Charles Parish Planning and Zoning to say for your address, on (985) 783-5060.

How the cut is made good

Our practice: a core is patched as soon as weather and access allow, with materials compatible with the roof covering, and on a roof under warranty the warranty terms are checked before any core is cut.

We keep the number of cores to what the finding needs.

What goes in the written trace

Where applicable, the covering and the method used, the likely entry point photographed and marked on a roof plan, the layers seen in any core and where it was taken, and our recommended repair.

Where a trace is inconclusive we say so, and say what would settle it.

Water on a flat roof may not stay where it entered

On a low-slope commercial roof the place water shows below is often not the place it came in. These are the habits that keep a trace from chasing the stain, and they are what we generally follow on a building we trace.

Water travels

Water can sometimes run along the deck and through insulation before it shows on a ceiling or a wall.

The stain is a clue, and the trace works from it to the drains and details that could feed it.

Perimeter and details first

In our experience, leaks on a commercial membrane are often found at seams, penetrations, curbs and edge terminations rather than in the open field.

Those details are checked closely before an open-field search begins. The commercial repairs page covers how they are repaired.

Tenants below

Commercial leak work often happens over a working business, so what sits below shapes the method and the work window.

Where a flood test could put water into a space that cannot take it, another method is used.

Big Easy Roofing Process

Four steps. The covering helps decide the method, and a core cut can check the result at one spot.

A worker in a hard hat and work gloves reviewing a form on a clipboard
01

01 Identify the covering

Single-ply membrane, built-up, modified bitumen or metal, or a sloped covering such as shingles, slate or wood.

02

02 Choose the method

Electronic or controlled flood test where the system and a qualified assessment allow, otherwise reading from the stain, seams and details, with manufacturer suitability checked first.

03

03 Check with a core where it matters

A small section removed at a selected spot, read, photographed and patched as soon as weather and access allow.

04

04 Write the trace and the scope

The likely entry point, our recommended repair, the layers seen in any core, and the permit question for Planning and Zoning on (985) 783-5060.

Everything else we do in St. Rose

The rest of the Big Easy Roofing services available in St. Rose, each with its own page and scope of work. Where a leak has wet the insulation, the commercial inspection page covers the moisture survey that follows, and the repair is scoped once both are done.

Filter by service type:

St. Rose Commercial Roof Leak Detection FAQs

The test methods, the core cut, the layer rule, and how the scope is priced.

Topic

Question not here?

Ask us about a commercial roof leak in St. Rose. No charge and no obligation.

Call (504) 800-8196
Which leak detection method is best for a membrane roof?

It depends on the membrane, the area and whether the structure can carry a flood test. Electronic suitability is checked against the manufacturer first, and on a warranted roof the warranty terms are checked before a destructive test.

Do you need to cut the roof to find a leak?

Not always. A leak can sometimes be traced without cutting. A core cut is used where a reading needs checking at one spot, and our practice is to patch it as soon as weather and access allow.

Why does the number of coverings matter?

For areas where wind design is required, the regional roofing handout says new roof coverings shall not be installed without first removing all existing layers where the roof has two or more applications of coverings. A core cut shows the layers at the spot where it is taken. Whether they count as separate applications, and what the rule means for your building, is for the building official.

Does a leak repair need a permit in St. Rose?

That is for St. Charles Parish Planning and Zoning to say for your address, on (985) 783-5060.

When does a leak repair become a bigger scope?

In our experience the answer is when the trace finds wet insulation across a larger area rather than at one defined entry point. In our experience the repair is then compared with a replacement. If a replacement or recover is being considered, two or more coverings already on the roof also matter under the handout rule.

Can you guarantee the leak will not return?

No. We trace the likely entry point and scope the repair, and say so plainly where a trace is inconclusive. In our experience a repair made without a likely entry point is hard to rely on.

What does commercial leak detection cost?

It is scoped to the roof, the method and the access, so the price follows a look at the building.

Will my insurance cover the leak repair?

That is a question for your insurer. Louisiana R.S. 37:2159.1 bars a roofing contractor from acting as a public adjuster or interpreting insurance policy coverage, so we document the physical condition and give an estimate.

Get the leak traced to the likely entry point and the layers recorded where a core is cut

We identify the covering, choose the method for it, confirm with a core where it matters, and write the scope with what we found. If you would rather start in writing, tell us what the job involves and we will come back with an estimate.

Call (504) 800-8196
Commercial Roof Leak Detectionin St. Rose