Big Easy Roofing Logo
Claim Banner - Big Easy Roofing Big Easy Roofing roof replacement guarantee banner
Call Our Roofing Experts!(504) 800-8196
Home/Service Areas/Louisiana/Slidell/Siding Installation

Siding Installation in Slidell, LA

Big Easy Roofing installs siding across Slidell and the eastern end of the St. Tammany Parish north shore. Siding changes a wall, which can matter on an Olde Towne Slidell address because exterior alterations in the district may be a Certificate of Appropriateness question. The written scope flags that step where it applies.

Written scopeWhat you get
Olde TowneMay add COA step on district addresses
WRB + flashingBehind every cladding system
Two officesPermit vs OTPDC are separate

Slidell siding installation at a glance

A siding installation on a Slidell house is a wall-system scope: a water-resistive barrier behind the cladding, flashing at every window, door and penetration, then the cladding and trim. Two paperwork questions sit on top of the carpentry. The first is whether the scope needs a city permit. The second is whether, on an Olde Towne address, the exterior alteration asks for a Certificate of Appropriateness conversation.

Material fit is a humidity question

Before it is a brochure question

North-shore humidity and wind-driven rain are part of the exposure every Slidell cladding sits in. The site visit selects material and finish against the exposure of each elevation on the specific house, not from a sample board on a counter.

Olde Towne may add a step

Design guidelines in city code Sec. 2.2217

For an address in the Olde Towne district, an exterior cladding alteration can be a Certificate of Appropriateness question. The City OTPDC page names the design guidelines at city code Sec. 2.2217; the deep detail of the OTPDC route lives on the Slidell roof-repairs page.

WRB and flashing are the wall system

Not an upgrade line item

A water-resistive barrier behind the cladding and flashing at every penetration are what keep wind-driven rain out of the wall. The scope names the WRB and flashing method before it names the cladding brand.

Paint-and-seal at penetrations

A common failure path

The seal around windows, doors, outlets and penetrations is a common place for water to enter a wall. The scope specifies the sealant grade and the weather window the paint and sealant are applied in.

City permit question

A Building Safety question

Whether a specific siding scope needs a city permit is a question for the City Building Safety office at (985) 646-4323 at 250 Bouscaren Street, with the Tyler EnerGov Self-Service online portal for submission.

What we will not interpret

Insurance or design guidelines

Under R.S. 37:2159.1 a Louisiana residential roofing contractor may not interpret your insurance cover. The OTPDC design guidelines are a city document, not ours; the commission is the body that reviews a cladding application on a district address.

Every figure on this page is an estimate, not a quote, and is subject to Big Easy Roofing sign off. Call Big Easy Roofing on (504) 800-8196 to walk every elevation of your Slidell house.

Cladding material fit on a lake-adjacent house

Material selection is a humidity, finish and maintenance question before it is a brochure question. The table lists the common Slidell cladding families and how each one tends to be maintained.

CladdingHumidity notesFinish and maintenanceOlde Towne step
Fibre cementDimensionally stable in humid airPainted finish; repaint on cycle set by product and exposureMay apply on district addresses
Engineered woodFinish is the moisture barrierPainted finish; repaint on cycle set by product and exposureMay apply on district addresses
VinylNo paint cycle; colour fades over timeReplacement rather than repaintMay apply on district addresses
Wood (clapboard, cedar)Needs sealed back and endsPainted or stained finish; shorter repaint cycle on exposed wallsMay apply on district addresses
Brick or stone veneerMasonry; a different tradePointing and sealing at mortar jointsMay apply on district addresses

No figures on this row are a quote. Whether a specific cladding material and finish is acceptable on an Olde Towne address is for the commission to answer; the scope flags the step, the city confirms it.

Olde Towne and the permit route, two separate offices

Two paperwork questions can apply to a siding scope in Slidell, and they sit with two different offices. The city permit question is a City Building Safety question. The Olde Towne Certificate of Appropriateness question sits with the OTPDC under City Planning.

Olde Towne, in short

Design guidelines in city code Sec. 2.2217

The OTPDC design guidelines are published in city code Sec. 2.2217 (municode section S2.22SUDIRE). On an Olde Towne address, an exterior cladding alteration can ask for a Certificate of Appropriateness. The categories and the admin-or-commission split sit on the Slidell roof-repairs page.

Where the OTPDC question is answered

City Planning, not us

The OTPDC sits under City Planning; the design guidelines are the commission document. The scope flags the OTPDC question on a district address; the city answers whether the specific scope engages the commission.

City permit question

(985) 646-4323

Whether a specific siding scope needs a city permit is a City Building Safety question. The office sits at 250 Bouscaren Street, with the Tyler EnerGov Self-Service online portal for submission.

Who decides which applies

The city, not us

The scope flags the paperwork question honestly. Building Safety answers the permit question; the OTPDC under City Planning answers the Certificate of Appropriateness question.

Why we flag it in the scope

A siding scope quoted without the Olde Towne flag on a district address can run into the commission conversation partway through. Naming the step at the start keeps the schedule honest.

Where the city confirms neither a permit nor a COA applies, the project moves straight into the wall-system work.

What we do not interpret

The scope does not read the design guidelines on behalf of the city. The guidelines are the commission document and the commission call.

What the scope does is submit through the city process on the specific cladding scope, with the elevations and penetrations named.

The exposure every cladding on much of Slidell sits in

A cladding system on a Slidell house sits in humid air, long paint-dry windows and wind-driven rain. Those three conditions drive the scope before any material is chosen.

Humidity holds back paint cure

Humid air slows paint cure, and paint applied in the wrong window can fail ahead of schedule. The scope names the product grade and the weather window the finish is applied in.

Paint that fails early is a full repaint, not a cheap touch-up, so care on application is cheaper than redoing it.

Wind-driven rain against vertical walls

Rain driven horizontally against a wall works on the seal at every penetration: windows, doors, hose bibs, outlets, vents. The scope specifies the sealant method and material grade at each.

A wall that photographs intact can leak at one poorly sealed window on an exposed elevation; the scope treats every penetration, not only the obvious ones.

Olde Towne elevations carry an extra review

An Olde Towne address can bring an OTPDC Certificate of Appropriateness conversation on an exterior alteration. The scope names the elevations in scope so the application is specific.

The scope separates the carpentry from the commission question; the commission reviews the exterior alteration, Building Safety reviews the permit.

Big Easy Roofing Process

Four steps. Olde Towne status and the city permit question are confirmed before any material is ordered.

A roofer inspecting siding on a residential elevation
01

01 Walk every elevation

Each elevation is photographed, with condition of existing cladding, trim, penetrations and finish noted. Olde Towne status flagged for the scope.

02

02 Confirm the paperwork route

City Building Safety confirms whether the scope needs a city permit. On an Olde Towne address, the OTPDC Certificate of Appropriateness question is raised with the city.

03

03 Scope the wall system and the finish

Water-resistive barrier, flashing at every penetration, cladding material and trim selected against the exposure of each elevation. The scope lists every item: tear-off, WRB, flashing, cladding, trim, finish, sealing.

04

04 Install, paint in the right window, photograph

Install work carried out, finish applied in the weather window the scope names, finished detail photographed on each elevation.

Everything else we do in Slidell

The rest of the Big Easy Roofing services available in Slidell, each with its own page and written scope. A siding scope often rides with soffit and fascia work; those pages name the adjoining items.

Filter by service type:

Slidell Siding Installation FAQs

The questions worth asking before a siding install on a Slidell house.

Topic

Question not here?

Ask us anything about siding on your Slidell house. No charge to ask.

Call (504) 800-8196
What does a siding installation include?

Tear-off of existing cladding where needed, a water-resistive barrier behind the new cladding, flashing at every window, door, outlet, hose bib and vent, new cladding and trim, finish, and sealing at every penetration. The scope lists each item.

What if my house is in the Olde Towne district?

An exterior cladding alteration on a district address can be a Certificate of Appropriateness question. The OTPDC design guidelines sit in city code Sec. 2.2217 and the OTPDC is under City Planning; the city answers whether a specific siding scope engages the commission.

Does siding installation need a city permit in Slidell?

The City Building Safety office at (985) 646-4323 answers that question. The office is at 250 Bouscaren Street and takes online submissions through the Tyler EnerGov Self-Service portal.

Which cladding material is best for my Slidell house?

The site visit answers that. Material selection is a humidity, finish and OTPDC-fit question tied to the specific elevations, not a general rule for the city as a whole.

How long does a cladding finish last?

That depends on the product, the exposure of the elevation and the weather window the finish was applied in. The scope names the product and the window for the chosen cladding and elevation.

What causes a cladding failure?

A common path is the seal around windows, doors and penetrations where wind-driven rain gets behind the cladding. The scope specifies the sealing method and material grade at every penetration before the cladding goes on.

Why does the water-resistive barrier matter?

The WRB is the drainage plane behind the cladding. Cladding sheds most of the rain but not all of it; the WRB and flashing at penetrations are what keep what gets through from reaching the sheathing.

Will my insurance pay for siding?

That is a question for your insurer. Under R.S. 37:2159.1 a Louisiana residential roofing contractor may not interpret your insurance cover.

Walk every elevation, flag the paperwork before any material is ordered

A siding scope that confirms Olde Towne status, names the city permit route, and specifies the WRB, flashing and seal detail at every penetration keeps the paperwork and the carpentry honest from day one. If you would rather start in writing, tell us what the job involves and we will come back with an estimate.

Call (504) 800-8196
Siding Installationin Slidell