Roof Flashing Repair in Slidell, LA
Big Easy Roofing repairs flashing across Slidell and the eastern end of the Lake Pontchartrain north shore in St. Tammany Parish. The scope is written specifically about the detail that is failing, with the City Building Safety office at (985) 646-4323 named as the office that decides whether the scope needs a permit.
Slidell roof flashing repair at a glance
A flashing repair fixes the sheet-metal seal between the roof covering and another surface, usually a wall, a chimney, a vent, or a pipe. On a Slidell roof the scope names which detail is failing and whether the City Building Safety office needs to see the work before it is done.
A specific detail, written down
The scope names which flashing is being repaired: chimney step flashing, counter flashing, wall junction, pipe boot, vent collar or edge metal. “Fix the flashing” is not a scope.
The City Building Safety office decides
Whether a specific flashing scope needs a city permit is for the City Building Safety office to say. We write the scope specifically enough that the office can answer, and we do not tell you the job is exempt from a permit on our own say-so.
Olde Towne may add a step
For an address in the Olde Towne district, visible exterior flashing replacement may be a Certificate of Appropriateness question. The City Olde Towne Preservation District Commission page publishes the regulatory basis in Sec. 2.2217; the deep detail of the OTPDC route sits on the Slidell roof-repairs page.
A flashing scope follows a trace
A flashing repair that does not know which flashing is failing is guessing. A leak trace identifies the entry point so the flashing scope knows where to cut and reseal.
What we will not do at a flashing
Under R.S. 37:2159.1 a Louisiana roofing contractor may not interpret your insurance cover. We write the scope and photograph the detail; your insurer reads your policy.
When a repair becomes a reroof
A flashing that cannot be reset without opening up more roof than a repair justifies is a repair or a replacement conversation, not a flashing scope.
Every figure on this page is an estimate, not a quote, and is subject to Big Easy Roofing sign off. Call Big Easy Roofing on (504) 800-8196 to look at a flashing on your Slidell roof.
Which flashing is failing, and where it is on the house
Flashings are not interchangeable. The table lists the common Slidell cases and what each repair involves, so a homeowner can see which detail is being discussed before any work starts.
| Flashing | Where on the house | What the repair involves | Permit question |
|---|---|---|---|
| Chimney step and counter flashing | Where the chimney meets the roof | Cut out old step flashing, install new, counter flashing re-mortared or re-sealed | Scope-dependent; City Building Safety answers |
| Wall junction flashing | Where a roof meets a vertical wall | Step flashing cut out and re-installed under the siding or counter | Scope-dependent |
| Pipe boot | Where a plumbing stack passes through | Old boot cut off, new boot installed, re-sealed | Scope-dependent; City Building Safety answers |
| Vent collar | Where a vent pipe passes through | Old collar removed, new collar installed, re-sealed | Scope-dependent; City Building Safety answers |
| Edge metal and drip edge | At eaves and rakes | Replace rusted or damaged edge metal with new | Scope-dependent; often part of a wider edge job |
Every figure is an estimate and none of it is a quote. A permit question on any of these is for the City Building Safety office on (985) 646-4323, not for us.
The city permit route on a flashing scope
The city publishes the office that handles roofing permits and the codes it inspects to. For a flashing scope that stops short of a reroof, the question is whether the specific scope needs a permit, which is the office’s call.
City Building Safety office
The City of Slidell Building Safety office at 250 Bouscaren Street handles permit intake, with online submission through the Tyler EnerGov Self-Service portal.
Adopted codes
The City Building Safety page lists the 2021 International Building Code, the 2021 International Residential Code and the 2021 International Existing Building Code, along with the 2020 National Electrical Code, among the codes it enforces. The 2021 IEBC is typically the code edition that governs work on an existing building, including a flashing scope that touches a reroof threshold.
Olde Towne route
For an address in the Olde Towne district, City of Slidell code Sec. 2.2217 establishes the Olde Towne Preservation District Commission, and visible exterior work can require a Certificate of Appropriateness. The deep detail sits on the Slidell roof-repairs page.
Where the OTPDC detail lives
The categories the city code lists, the admin-or-commission split and the full OTPDC route sit on the Slidell roof-repairs page. The Building Safety office on (985) 646-4323 confirms whether a specific flashing scope engages the commission before the application is drafted.
What we hand the city
A scope specific enough to answer the permit question: which flashing, what is being cut out, what is being installed, which materials. “Fix the flashing” is not specific; “cut and replace step flashing on the west wall of the chimney” is.
With that in hand, the City Building Safety office can say whether the scope needs a permit or not. Either answer is fine; a vague answer is not.
What we do not tell the city
We do not tell the City which flashings need or do not need a permit. That is the city’s book, not ours.
We write the scope. The office decides.
Where flashings fail on a lake-adjacent house
Lake Pontchartrain humidity near the Rigolets drives corrosion on metal flashings, and wind-driven rain off the lake works horizontally against vertical surfaces. The common Slidell flashing failures sit at the junctions where those two forces meet.
Metal corrosion where it matters most
Humidity accelerates corrosion on exposed metal, and the exposed metal that matters most is the flashing on a chimney, the counter flashing stepped into mortar, and the edge metal at the eaves.
The scope reads the condition of the metal, not just the sealant above it.
Wind-driven rain against vertical surfaces
When rain is driven horizontally, water hits the back of a vent cap, the exposed face of a chimney flashing, the side of a dormer. Those are the surfaces the scope photographs.
A flashing that reads clean from one angle can be failing on the lake-facing side; photographs from both sides tell the story.
Older houses have different flashings
Many Olde Towne Slidell houses have deeper mortar joints and original step flashing details, which are different work from a modern pipe boot on a post-2000 house along the Fremaux Avenue or Gause Boulevard corridors. The scope adapts to what is on the house.
A chimney flashing on an older house is often part of an Olde Towne conversation; the City Building Safety office knows which.
Big Easy Roofing Process
Four steps. The flashing is photographed before anything is cut out, so the scope and the work are tied to the same evidence.

01 Trace to the failing detail
A leak trace identifies which flashing is failing before the scope is written. Photographs record the detail and the surrounding roof.
02 Write the scope and confirm the permit route
The scope names the detail, the materials and the method. If the address is in the Olde Towne district or the scope might need a permit, the scope says so.
03 Permit where it applies
The City Building Safety office answers the permit question. An Olde Towne scope may add a Certificate of Appropriateness step under Sec. 2.2217.
04 Cut, install, photograph
Old flashing cut out, new installed, re-sealed with manufacturer-specified materials, finished detail photographed before the ladders come down.
Everything else we do in Slidell
The rest of the Big Easy Roofing services available in Slidell, each with its own page and written scope. A flashing repair often follows a leak trace, which identifies the entry point; a flashing scope that does not know which detail is failing is guessing.

Roof Replacement in Slidell
Read More
Roof Repairs in Slidell
Read More
Roof Inspection in Slidell
Read More
Hail Damage Roof Repair in Slidell
Read More
Storm Damage Roof Repair in Slidell
Read More
Storm Damage Emergency Response in Slidell
Read More
Emergency Roofing in Slidell
Read More
Roof Leak Detection in Slidell
Read More
Roof Maintenance in Slidell
Read More
Roof Coating in Slidell
Read More
Roof Ventilation in Slidell
Read More
Roof Weatherproofing in Slidell
Read More
Roof Restoration in Slidell
Read More
Fascia Board Installation and Repair in Slidell
Read More
Gutters and Downspouts Installation in Slidell
Read More
Gutters and Downspouts Repair in Slidell
Read More
Siding Installation in Slidell
Read More
Asbestos Roof Removal in Slidell
Read More
Roof Damage Documentation in Slidell
Read More
Commercial Roof Replacement in Slidell
Read More
Commercial Roof Repairs in Slidell
Read More
Commercial Roof Inspections in Slidell
Read More
Commercial Hail Damage Repair in Slidell
Read More
Commercial Re-Roofing in Slidell
Read More
Commercial Roof Coating in Slidell
Read More
Commercial Elastomeric Coatings in Slidell
Read More
Commercial Roof Ventilation in Slidell
Read More
Commercial Roof Leak Detection in Slidell
Read More
Commercial Siding Installation in Slidell
Read MoreSlidell Roof Flashing Repair FAQs
The questions worth asking before a flashing repair on a Slidell roof.
Topic
Question not here?
Ask us anything about a flashing on your Slidell roof. No charge to ask.
Call (504) 800-8196Which flashings do you repair?
Chimney step and counter flashing, wall junction flashing, pipe boots, vent collars and edge metal at eaves and rakes. The scope names the specific detail.
Does a small flashing repair need a city permit?
Whether a specific flashing scope needs a city permit is a question for the City Building Safety office at (985) 646-4323. The Building Safety page lists the 2021 IBC, IRC and IEBC along with the 2020 National Electrical Code among the codes it enforces, and the office answers scope-level questions.
What if my address is in the Olde Towne district?
City of Slidell code Sec. 2.2217 establishes the Olde Towne Preservation District Commission, and visible exterior work can require a Certificate of Appropriateness. The deep detail of the OTPDC route sits on the Slidell roof-repairs page, and the City Building Safety office confirms whether a specific flashing scope engages the commission.
Do I need a leak trace before a flashing repair?
Usually, yes. A flashing scope that does not know which flashing is failing is guessing. The leak detection page covers that trace.
What is the difference between a pipe boot and a flashing?
A pipe boot is the specific flashing around a plumbing stack. “Flashing” is the general term for the sheet-metal seal between the roof covering and another surface, so a pipe boot is one kind of flashing.
Can you re-seal a flashing without cutting it out?
Sometimes. If the metal is in good condition and only the sealant has failed, cleaning and re-sealing with manufacturer-specified materials is the right work. If the metal is corroded or deformed, re-sealing it is a short-term fix.
Will my insurance pay for a flashing repair?
That is a question for your insurer. Under R.S. 37:2159.1 a Louisiana roofing contractor may not interpret your insurance cover.
When is a flashing repair the wrong answer?
When the surrounding roof is near the end of its useful life or when the flashing cannot be reset without opening up more roof than a repair justifies. In those cases the conversation is a wider repair or a replacement.
Name the detail, confirm the permit route before any flashing is cut
A flashing scope that names the specific detail, confirms the city permit route with the City Building Safety office, and photographs the metal before and after is a scope that lasts. If you would rather start in writing, tell us what the job involves and we will come back with an estimate.
Call (504) 800-8196



