Big Easy Roofing Logo
Claim Banner - Big Easy Roofing Big Easy Roofing roof replacement guarantee banner
Call Our Roofing Experts!(504) 800-8196
Home/Service Areas/Louisiana/Slidell/Commercial Roof Ventilation

Commercial Roof Ventilation in Slidell, LA

Big Easy Roofing scopes and installs commercial roof ventilation in Slidell and across St. Tammany Parish. On a Slidell commercial roof, the roof side (each penetration) and the mechanical and electrical side (equipment and hookup) are scoped together before any equipment is proposed, and which filings a specific scope engages is confirmed by the office that covers the address during review of the submitted application.

Assembly firstWhere the moisture goes
Roof + equipmentScoped together, not after
(985) 646-4323City office, inside city limits
City or parishBy address

Slidell commercial roof ventilation at a glance

Many commercial roofs have no attic to vent, so the answer follows from the assembly under the membrane. On a Slidell commercial roof the roof side and the mechanical and electrical side are scoped together, with filings confirmed by the office that covers the address (City of Slidell Building Safety inside city limits, St. Tammany Parish outside) during review of the submitted application.

Assembly first

Where the moisture goes

The assembly is read before any vent or fan is proposed. On a conventional commercial low-slope roof, interior humidity is typically handled by the HVAC, while air barriers, vapor-control layers and insulation address other moisture transfer, rather than passive roof vents.

Inside city limits

City Building Safety

City of Slidell Building Safety at 250 Bouscaren Street on (985) 646-4323 is the office for an address inside city limits. Which filings a scope engages is confirmed with the office during review of the submitted application.

Outside city limits

St. Tammany Parish

For addresses in unincorporated St. Tammany Parish outside Slidell city limits, St. Tammany Parish Permits and Inspections on (985) 898-2574 is the office that covers the address.

Which filings a scope engages

For the office that covers the address

Which specific filings (building, mechanical, electrical) a commercial ventilation scope engages is confirmed by the office during review of the submitted application. We do not say in advance that a given vent or fan requires a given filing.

The roof side

Each curb and penetration detailed

Each curb, duct, pipe and penetration that passes through the roof to a rooftop unit, fan or vent is flashed and detailed as its own line in the written scope.

What we will not interpret

Your insurance

A written scope documents what we found and what the work involves. We do not interpret your insurance coverage; that is for your insurer and your policy.

Commercial ventilation work is scoped to the roof and the equipment, so call Big Easy Roofing for a scoped price.

Four common commercial roof assemblies and where the moisture goes

The ventilation answer on a commercial roof follows from the assembly under the membrane. Four common assemblies put the insulation, and the moisture path, in different places. The assembly is read first so a house-attic answer is not applied where there is no attic. These rows are general trade tendencies, not an exhaustive list.

AssemblyInsulation locationMoisture pathVentilation service
Conventional low slopeAbove the deck, under the membraneInterior humidity is typically handled by the HVAC; air barriers, vapor-control layers and insulation address other moisture transferPoint-source exhaust from occupancy, kitchens or equipment is a common service; whether passive roof vents are used depends on occupancy, HVAC design and the specific assembly
Protected membraneAbove the waterproofing membraneAir and vapor control depend on the assembly's declared air and vapor-control layersAs conventional
Metal buildingVaries by system (between purlins, above the deck, below panels or in a liner system)Depends on the insulation system and facingRooftop equipment with each penetration detailed through the panel; ridge or other passive venting where the system calls for it
Ventilated attic, older buildingsAt the ceiling plane, below an enclosed space under the deckCross ventilation of the enclosed spacePassive venting scaled to the space, plus exhaust where needed

These are general trade characteristics, not code text. The assembly is read on the roof before any ventilation work is scoped, and the manufacturer installation instructions and project documents govern any product-specific requirement, subject to applicable code and authority requirements.

Office and filings, for a Slidell commercial ventilation scope

A Slidell commercial ventilation scope is prepared for submission to the City of Slidell Building Safety office for an address inside city limits, or to St. Tammany Parish Permits and Inspections for an address in unincorporated St. Tammany Parish outside Slidell city limits. Which specific filings the scope engages is confirmed by the office during review of the submitted application, rather than named in advance.

How the filings side is settled

By the office that covers the address

Which filings (building, mechanical, electrical) a specific commercial roof ventilation scope engages is confirmed by the office that reviews the submitted application, not named in advance.

Inside city limits

City Building Safety

The City of Slidell Building Safety office at 250 Bouscaren Street on (985) 646-4323 handles the permit filings for an address inside city limits. Which filings a specific scope engages is reviewed with the office during review of the submitted application.

Outside city limits

St. Tammany Parish

For an address in unincorporated St. Tammany Parish outside Slidell city limits, St. Tammany Parish Permits and Inspections at stpgov.org on (985) 898-2574 is the office that covers the address. The parish and the city are separate offices, so the file goes to the one that covers the address.

What the written scope names

Assembly, penetrations, equipment, office

The roof assembly, each rooftop penetration, the mechanical equipment proposed, the electrical hookup and the office that covers the address are each named in the written scope.

How the two sides sit

The roof-side answer is on the roof: each penetration flashed and detailed as roof work. The office-side answer is in the permits file: the office confirms which filings apply to the submitted scope during review of the application.

The written scope names the roof assembly and the office route before the application is submitted.

Where a penetration leaks

The commercial leak page covers tracing water at a rooftop penetration, which is a common reason a ventilation change is scoped in the first place.

Each rooftop opening is detailed in the scope that follows.

When Olde Towne review may apply

Where the building sits in the Olde Towne Preservation District and visible rooftop equipment may be a visible change from the street, the Olde Towne Design Guidelines (Sec. 2.2217) may apply with administrative or commission review on top of the normal permit question. Ask the office which route applies.

Why it matters on a Slidell commercial building

Commercial roofs in Slidell see Louisiana rain and humid summers. Interior humidity is typically handled by the HVAC, while air barriers, vapor-control layers and insulation address other moisture transfer, rather than passive roof vents. The assembly, the penetrations and the mechanical and electrical side are each named in the written scope so none is left to the field.

Humid air inside

On a conventional commercial low-slope roof, interior humidity is typically handled by the HVAC, while air barriers, vapor-control layers and insulation address other moisture transfer, rather than passive roof vents.

That is why the assembly is read first.

Penetrations and curbs

Each curb, duct, pipe and penetration that passes through the roof to a rooftop unit, fan or vent is another opening in the membrane.

Each one is flashed and detailed as its own line in the written scope, not left to the field.

For houses

A house attic is a different problem, with intake, exhaust and attic ventilation.

The residential ventilation page covers it.

Big Easy Roofing Process

Four steps. The assembly, the office and the filings come before any equipment is proposed.

A roofer checking rooftop exhaust equipment on a commercial roof
01

01 Read the assembly

Insulation position and the moisture path, read on the roof.

02

02 Confirm which office covers the address

City of Slidell Building Safety at 250 Bouscaren Street on (985) 646-4323 inside city limits, or St. Tammany Parish Permits and Inspections on (985) 898-2574 for an address in unincorporated St. Tammany Parish outside Slidell city limits.

03

03 Scope the roof and the equipment, prepared for submission

Each penetration detailed as roof work; the mechanical equipment and the electrical hookup named for the office. The office confirms which filings apply during review of the submitted application.

04

04 Install and record

Each penetration flashed and photographed as project documentation, with any required inspections scheduled per office procedure.

Everything else we do in Slidell

The rest of the Big Easy Roofing services available in Slidell, each with its own page and scope. For houses, the residential ventilation page covers attic ventilation, intake and exhaust.

Filter by service type:

Slidell Commercial Roof Ventilation FAQs

The city or parish office route, which filings a scope engages, commercial roof assemblies, and how the work is priced.

Topic

Question not here?

Ask us about ventilation on a commercial roof in Slidell. No charge and no obligation.

Call (504) 800-8196
Which office takes a commercial ventilation permit in Slidell?

Inside city limits the City of Slidell Building Safety office at 250 Bouscaren Street on (985) 646-4323. For addresses in unincorporated St. Tammany Parish outside Slidell city limits, St. Tammany Parish Permits and Inspections on (985) 898-2574.

Which filings does a commercial ventilation scope engage?

Which filings (building, mechanical, electrical) a specific commercial roof ventilation scope engages is confirmed by the office that covers the address during review of the submitted application, rather than named in advance.

Does adding a rooftop fan need a mechanical filing?

We do not say either way. Which filings (building, mechanical, electrical) a specific scope engages is confirmed by the office during review of the submitted application. Inside city limits that is the City of Slidell Building Safety office on (985) 646-4323.

Does a flat commercial roof need roof vents?

Many commercial roofs have no attic to vent. The assembly is read first, and on a conventional commercial low-slope roof interior humidity is typically handled by the HVAC, while air barriers, vapor-control layers and insulation address other moisture transfer, rather than passive roof vents.

Does Olde Towne review apply to rooftop equipment?

Where the building sits in the Olde Towne Preservation District and the rooftop equipment may be a visible change from the street, the Olde Towne Design Guidelines (Sec. 2.2217) may apply with administrative or commission review on top of the normal permit question. Ask the office which route applies.

Will my insurance cover commercial ventilation work?

That is a question for your insurer. We do not interpret your insurance coverage; we document the physical condition and provide an itemized estimate.

What does commercial roof ventilation work cost?

It is scoped to the roof and the equipment after the assembly is read.

Get the roof and the equipment scoped together on a Slidell commercial building

We read the assembly, confirm which office covers the address, and detail every penetration as roof work alongside the mechanical and electrical equipment in a written scope prepared for submission to that office. If you would rather start in writing, tell us what the job involves and we will come back with an estimate.

Call (504) 800-8196
Commercial Roof Ventilationin Slidell