FREE Roofing Estimates
24 Hour Roof Replacement Guarantee
Call Icon
    Top

Call Our Roofing Experts! (504) 800-8196

Home/Service Areas/Louisiana/Metairie/Siding Installation

Siding Installation in Metairie, LA

Big Easy Roofing installs and replaces exterior siding across Metairie and unincorporated Jefferson Parish, licensed by the Louisiana State Licensing Board for Contractors. Most Metairie siding jobs price out between $3 and $18 per square foot of wall depending on the material, and Jefferson Parish does not require a permit to replace non structural exterior wall covering on a one or two family home.

$3 to $18 /sq ftEstimated installed
5 to 10 daysTypical whole home
No permitNon structural replacement
High wind ratedFiber cement, to the tested assembly

Metairie siding installation at a glance

A Metairie siding installation is priced on wall area, not floor area. Vinyl runs about $3 to $8 per square foot installed, engineered wood $5 to $12, aluminum $6 to $12 and fiber cement $6 to $18. Jefferson Parish requires no permit to replace non structural wall covering on a one or two family home.

Estimated cost per sq ft

$3 to $18

Wall area, installed. Vinyl sits at the bottom of the band and fiber cement at the top on a Metairie home.

Whole home estimate

$6,000 to $16,000

Vinyl siding on a typical single storey Metairie home, installed. Fiber cement on the same house prices well above it.

Permit authority

None

Jefferson Parish lists replacement of vinyl siding or other non structural exterior wall covering on one and two family dwellings as work that does not need a permit.

Materials offered

Vinyl, wood, fiber cement

Vinyl (cheapest), engineered wood (factory finished), aluminum (will not rot or burn) and fiber cement (does not rot, does not feed termites).

Typical timeline

5 to 10 days

Whole home re side on a Metairie house, weather dependent. A single elevation is usually two to three days.

Warranty

1 yr workmanship

One year workmanship warranty on the installation, on top of whatever the manufacturer warrants on the material itself.

Every figure on this page is an estimate, not a quote, and is subject to Big Easy Roofing sign off. Cost and timescale depend on size, pitch, access, weather, materials and whatever is found once work starts, so call Big Easy Roofing on (504) 800-8196 and we will come out and give you an estimate for your own roof.

Siding is a rain screen, not a seal. It sheds the bulk of the water and the weather resistive barrier behind it handles whatever gets past. That distinction decides how a Metairie re side is scoped, because most of the wall failures we open up are failures of the housewrap, the window flashing or the kick out flashing where a roof meets a wall, and not of the siding panel at all.

Pricing is per square foot of wall area. Big Easy Roofing measures elevation by elevation, opens a test area to look at the sheathing before quoting, and prices the material options side by side so the choice between vinyl and fiber cement is made on numbers rather than on a recommendation. Where the sheathing behind the old siding has gone soft, that repair is written as its own line rather than buried in the square foot rate.

Estimated market ranges for a Metairie residential siding installation, installed, measured on wall area. Ranges vary with elevation height, trim detail, and the condition of the sheathing behind the existing siding.

Metairie siding materials and how each behaves on the Gulf Coast

Four materials cover almost every Metairie re side. Vinyl is the cheapest and most forgiving to install. Fiber cement costs the most and is the only one of the four that neither rots nor feeds a termite. The right answer depends on the budget, the exposure of the wall, and whether the address sits inside the Old Metairie conservation district.

MaterialWhat it isEstimated installed costHow it behaves on the Gulf Coast
VinylHollow extruded PVC panel, hung loose on the wall$3 to $8 per sq ftDoes not rot and gives termites nothing to eat. Moves a lot with temperature, so it has to be hung loose rather than nailed tight, and it can crack on hard impact.
Engineered woodWood strand board with a resin binder and a factory finish$5 to $12 per sq ftFactory treated against rot and insects and holds paint well. Every cut end has to be sealed on site or the treatment stops at the cut.
AluminumCoil formed metal panel with a baked finish$6 to $12 per sq ftWill not rot, will not burn and gives insects nothing. Dents on hail and on ladder knocks, and the dents do not come out.
Fiber cementCement, sand and cellulose board. James Hardie is the common brand$6 to $18 per sq ftDoes not rot and does not soak up water the way wood does, though like any cladding it needs its clearances and flashings. Does not feed termites. Published wind ratings commonly quoted up to 150 mph, for the specific tested assembly and fastening schedule rather than for the material as a category.
Whole home, vinylComplete re side of a typical single storey home$6,000 to $16,000The usual starting point for a Metairie budget, and it is a whole job figure rather than the per foot rate multiplied out. Fiber cement on the same house lands well above it.
Single elevationOne wall re sided, usually after storm or impact damagePriced per sq ftColour matching an older run is the hard part. Expect a discussion about whether one wall or the whole house is the honest answer.

Estimated market ranges only, not a quote. Call (504) 800-8196 for a written per square foot estimate on your Metairie home.

Permits, the conservation district and wind rating on a Metairie re side

Jefferson Parish does not require a permit to replace non structural exterior wall covering on a one or two family home, which covers an ordinary Metairie re side. Two things change that. Structural work behind the siding needs a permit, and an address inside the Old Metairie Neighborhood Conservation District goes through Jefferson Parish Planning before the material is chosen.

Jefferson Parish permit

None for a re side

The parish's own list of work that does not need a permit includes replacement of vinyl siding or other non structural exterior wall covering on one and two family dwellings, provided the covering meets Chapters 33 and 40 of the parish code. Rebuilding studs, sheathing or a header behind the siding is structural and does need a permit.

Old Metairie conservation district

Planning review

Addresses inside the Old Metairie Neighborhood Conservation District go through Jefferson Parish Planning before most exterior work, and the district's design standards restrict which cladding materials are acceptable. Confirm your address with Planning on (504) 736-6320 before a material is ordered, not after.

Wind and impact rating

Per tested assembly

Fiber cement products carry published high wind ratings, commonly quoted up to 150 mph, but the rating belongs to a specific tested assembly rather than to the material in general. Fastener type, fastener spacing, substrate and clearances are what earn it, and the figure for the product specified is confirmed against the manufacturer's own evaluation report. Big Easy Roofing installs to the published schedule for that reason.

Often claimed after a storm

Ask your insurer

Storm damage to siding is commonly claimed, but whether your policy covers a particular loss is decided by your insurer, not by us. Louisiana law prohibits a contractor from interpreting coverage. Big Easy Roofing photographs the damage and writes an itemised estimate, and the claim itself is between you and your insurer.

The wall behind the siding is the part that matters

A re side is the only time anyone sees the weather resistive barrier, the window flashing and the kick out flashing at the roof to wall junction. On a Metairie house those are where wind driven rain actually gets in, and they are cheap to correct while the wall is open and expensive to reach afterwards.

Big Easy Roofing opens a test area before quoting so the scope reflects what is behind the old siding rather than what we hope is behind it.

Fiber cement and vinyl give termites nothing

Formosan subterranean termites are established across the New Orleans area and they travel behind cladding, out of sight, where a routine inspection will not find them. Wood siding in contact with soil or splash is the classic entry.

Neither fiber cement nor vinyl is food for a termite. That is a large part of why they dominate Metairie re sides, and why a wood look is usually delivered in fiber cement rather than in wood.

Why Metairie siding fails where it does

Three failure patterns account for most of the Metairie siding Big Easy Roofing replaces. Water gets behind the cladding at a flashing rather than through it, termites travel up behind wood in contact with the ground, and vinyl nailed tight instead of hung loose buckles once a Gulf summer works on it.

Water entering at the flashings, not through the panel

Wind driven rain in Metairie arrives sideways. It does not pass through a siding panel, it goes around one, at the window head, at the base of the wall, and above all at the kick out flashing where a roof edge dies into a wall. Missing kick out flashing is the single most common cause of a rotten wall corner we open up.

The tell from outside is staining or soft trim below a roof to wall junction. The fix is flashing, not more caulk.

Formosan termites travelling behind the cladding

Formosan subterranean termites are established across the New Orleans area. They build shelter tubes in the dark and travel behind cladding where nobody is looking, so the first visible sign is often a soft spot in trim or a blistered panel long after the colony arrived.

Keeping cladding clear of the soil, and moving from wood to fiber cement or vinyl at the re side, removes both the highway and the meal.

Vinyl nailed tight instead of hung loose

Vinyl expands and contracts a long way across a Gulf Coast summer. It is designed to hang on the nail rather than be pinned by it, with the fastener centred in the slot and left about a sixteenth of an inch proud.

Nailed tight, the panel has nowhere to go and buckles in waves by the second summer. That is an installation fault, not a material fault, and it is the most common reason a Metairie vinyl wall looks wrong.

Big Easy Roofing Siding Process

Three steps from the first call to a finished wall: an on site measure with a test opening so the scope reflects what is actually behind the old siding, a written per square foot quote with the materials priced side by side, and an installation that flashes and wraps the wall before a single panel goes up. Call (504) 800-8196 to book the visit.

Contractor in a yellow hard hat and high visibility vest holding a clipboard at the front door of a house clad in grey lap siding
01

On site measure and test opening

Same week visit at the address. Wall area is measured elevation by elevation and a small test area is opened so the sheathing, the housewrap and the window flashing behind the existing siding can be seen rather than guessed at.

02

Written quote, materials side by side

The scope prices vinyl, engineered wood, aluminum and fiber cement against the same measured wall area, so the material decision is made on numbers. Any sheathing repair found at the test opening is written as its own line rather than hidden in the rate.

03

Wrapped, flashed, then clad

The wall is wrapped and the window heads, base and roof to wall kick outs are flashed before cladding starts. Panels go on to the manufacturer's fastening schedule, which is what the wind rating depends on.

Everything else we do in Metairie

The rest of the Big Easy Roofing services available in Metairie, each with its own page, crew and written scope. Where storm damage has taken both the wall and the roof covering, a Metairie roof replacement and the re side are usually scoped together so the roof to wall flashing is corrected once.

Filter by service type:

Metairie Siding Installation FAQs

The questions Metairie homeowners actually ask us about siding, answered before you have to pick up the phone.

Topic

Question not here?

Ask us anything about your Metairie siding. We usually answer the same day, no charge and no obligation.

Call (504) 800-8196
How much does siding installation cost in Metairie

Estimated ranges. Metairie siding runs about $3 to $18 per square foot of wall installed depending on the material. Vinyl sits at $3 to $8, engineered wood at $5 to $12, aluminum at $6 to $12 and fiber cement at $6 to $18. A complete vinyl re side on a typical single storey Metairie home typically lands between $6,000 and $16,000, which is a whole job figure rather than the per foot rate multiplied out.

Do I need a permit to replace siding in Metairie

Usually no. Jefferson Parish lists replacement of vinyl siding or other non structural exterior wall covering on one and two family dwellings among the work that does not require a permit, provided the covering complies with Chapters 33 and 40 of the parish code. Structural work behind the siding, such as replacing studs or a header, is a different matter and does need a permit.

Vinyl or fiber cement for a Metairie home

Fiber cement if the budget reaches it. It does not rot, does not soak up water the way wood does, and does not feed termites, and it carries published high wind ratings for the tested assembly when installed to the manufacturer's fastening schedule. Vinyl is the value choice and performs perfectly well when it is hung loose and flashed properly. Big Easy Roofing prices both against the same measured wall area.

Will new siding stop my house getting wet

Not on its own, and no siding does. Siding is a rain screen that sheds the bulk of the water, and the weather resistive barrier and flashings behind it handle what gets past. On the Metairie walls we open up, the water is almost always entering at a window head, at the base of the wall, or at a missing kick out flashing where a roof edge meets a wall, rather than through the panel.

Does siding stop Formosan termites

It removes the meal, not the colony. Formosan subterranean termites are established across the New Orleans area and travel behind cladding out of sight. Fiber cement, vinyl and aluminum give them nothing to eat, so moving off wood at the re side takes away the food source. Keeping the cladding clear of soil and splash matters just as much, and termite treatment itself is a pest control job, not a siding job.

How long does a whole home re side take in Metairie

Five to ten working days on a typical Metairie house, weather dependent. A single elevation is usually two to three days. Fiber cement takes longer than vinyl because the boards are heavier, the cuts are slower and the fastening schedule is stricter. Any sheathing repair found once the old siding is off adds time, which is why the test opening happens at the quote stage.

Can you re side while the roof is being replaced

Yes, and it is the sensible order where both are due. The kick out flashing and the step flashing where a roof edge meets a wall belong to both trades, and doing the two jobs together means that junction is built once, correctly, instead of being disturbed twice. The scopes stay itemised separately so the pricing is still legible.

What happens if you find rot behind the old siding

It gets photographed, measured and priced as its own line before anyone continues. Big Easy Roofing opens a test area at the quote stage precisely so that a soft sheathing panel is a known risk rather than a surprise invoice. Small areas of sheathing replacement are common on a Metairie house and are not a reason to stop the job.

Does homeowners insurance cover storm damaged siding in Louisiana

Storm damage to siding is commonly claimed, but whether a particular loss is covered is a question for your insurer or a licensed public adjuster. La. R.S. 37:2159.1 prohibits a Louisiana contractor from interpreting policy coverage, so we will not tell you what your policy pays. What we do is photograph the damage and write a good faith itemised repair estimate you can hand to whoever is handling the claim.

Do you side homes in Old Metairie and the conservation district

Yes, with one extra step. Addresses inside the Old Metairie Neighborhood Conservation District go through Jefferson Parish Planning before most exterior work, and the district's design standards restrict which cladding materials are acceptable. Confirm your address and the material with Planning on (504) 736-6320 before anything is ordered. Coverage otherwise extends across Metairie, Bucktown, Kenner, Harahan and River Ridge.

Book a Metairie siding measure

On site measure with a test opening so the scope is real, a written per square foot quote with vinyl, engineered wood, aluminum and fiber cement priced side by side, and the wall flashed and wrapped before any panel goes up.

Call (504) 800-8196
Siding Installin Metairie