Big Easy Roofing Logo
Claim Banner - Big Easy Roofing Big Easy Roofing roof replacement guarantee banner
Call Our Roofing Experts!(504) 800-8196
Home/Service Areas/Louisiana/River Ridge/Commercial Elastomeric Coatings

Commercial Elastomeric Coatings in River Ridge, LA

Big Easy Roofing applies elastomeric coatings to commercial roofs across River Ridge and the east bank of Jefferson Parish. The three common chemistries, acrylic, silicone and polyurethane, each handle the east-bank Jefferson envelope differently, and the leading failure mode on the specific roof decides which one fits.

Three chemistriesAcrylic, silicone, polyurethane
Leading failure modePonding, UV or traffic
ASTM D6083Common reference for acrylic
(504) 736-6957Jefferson Parish building permits

River Ridge commercial elastomeric coatings at a glance

An elastomeric coating is a flexible liquid-applied film over a sound commercial roof. The three common chemistries, acrylic, silicone and polyurethane, each handle the east-bank Jefferson envelope differently. ASTM D6083 is the published reference for acrylic coatings; silicone and polyurethane are specified from the manufacturer datasheet, which governs for a specific job.

Substrate first

The survey rules out some chemistries

The membrane or metal is walked and any leak is traced and repaired as its own scope before a chemistry is specified. A chemistry that is incompatible with the existing covering is ruled out at the survey rather than discovered on top of a wet substrate.

Ponding tolerance

Chemistry against standing water

Standing water on a low-slope roof is a load on the coating. Silicone chemistry usually tolerates sustained ponding better than acrylic; polyurethane varies by product. The product datasheet and the roof’s own ponding reading govern the specification together.

UV and reflectance

Where a bright field is wanted

Louisiana sun is a steady year-round load. Acrylic chemistry can hold a reflective finish on a field that drains cleanly; dirt pickup over time usually dims the finish rather than failing it. On a roof that ponds, acrylic is usually ruled out.

Foot traffic and abrasion

Where equipment is serviced

Where foot traffic across HVAC servicing paths or antenna runs is part of the roof’s life, polyurethane chemistry on the traffic lane, or a separate walkway pad, is specified alongside a different chemistry on the field.

ASTM D6083

Published reference for acrylic

ASTM D6083 / D6083M, published by ASTM International, sets the material and performance requirements for liquid-applied acrylic roof coatings, so a quote citing it can be read against a common reference rather than a product brochure’s own figures.

What we will not interpret

Your insurance

A written scope documents what we found and the chemistry we propose. Under R.S. 37:2159.1 a Louisiana roofing contractor may not interpret your insurance cover.

Elastomeric coating is priced on area, substrate and chemistry, so call Big Easy Roofing on (504) 800-8196 for a walk on your River Ridge commercial building.

Three chemistries, against three leading failure modes

Once the substrate has filtered the shortlist, three failure modes rank what is left: standing water, UV with dirt pickup, and foot traffic with abrasion. A chemistry that is a poor fit for the leading failure mode on a specific roof tends to underperform even when the datasheet reads well in isolation. The product datasheet governs for the specific job; this table carries the general trade characteristics.

ChemistryStanding waterReflectance and dirt pickupFoot traffic and abrasion
AcrylicSoftens under sustained ponding; usually ruled out on a roof that pondsGood on a field that drains; the published reference is ASTM D6083Poor on a traffic path
SiliconeUsually tolerates sustained ponding better than acrylic once curedUV-stable; can lose reflectance as dirt picks up over timeFair; slippery when wet
PolyurethaneVaries by product; the datasheet governsAliphatic types hold a finish longer than aromatic types under UVCommonly chosen where abrasion leads the failure modes

These are general trade characteristics. The product datasheet governs the specific chemistry on a specific roof, and compatibility with any existing coat is checked before a new coat goes on.

ASTM D6083 as a common reference, and how it reads on a quote

ASTM D6083 / D6083M, “Standard Specification for Liquid Applied Acrylic Coating Used in Roofing”, is the published industry reference for acrylic roof coatings. On a quote the standard is cited so one acrylic product can be read against another on apples-to-apples terms, rather than against a brochure’s own preferred figures. Silicone and polyurethane are specified from their own manufacturer datasheets, which govern for the specific job.

What ASTM D6083 is

The acrylic coating reference

ASTM D6083 is the published ASTM International standard that sets the material and performance requirements for liquid-applied acrylic coatings used in roofing, so a specifier can compare two acrylic products against the same benchmark.

What it does not cover

Silicone and polyurethane

ASTM D6083 is specific to acrylic. Silicone and polyurethane coatings are specified from the manufacturer datasheet for the specific product; the datasheet governs ponding tolerance, reflectance, abrasion and the preparation required.

How it reads on a quote

The citation sits next to the chemistry

A quote that names an acrylic coating and cites ASTM D6083 lets the number next to it be read against the same requirements another acrylic quote would be read against. A quote that names only a trade brand name without a published reference does not.

The parish permit question

For the specific scope

Whether a commercial coating scope needs a parish permit is confirmed with the Jefferson Parish East Bank building permits office on (504) 736-6957 by the specific address and scope. The office answers scope-by-scope rather than from a published rule on coatings.

How ASTM D6083 and the datasheet sit together

The published standard is the floor: an acrylic coating listed to ASTM D6083 has met the material and performance requirements the standard specifies.

The manufacturer datasheet is where the specific product’s preparation, mil thickness, cure window and recoat window are stated. The datasheet governs for a specific job even where the ASTM standard sits behind it.

What a coating is not

An elastomeric coating is not a reroof under the parish commercial-reroof conversation, and it is not a recover under the code test on the commercial roof coating page.

Where the survey shows a roof past the end, the commercial roof replacement page carries the next conversation.

East-bank Jefferson envelope on a commercial coating

The east bank of Jefferson Parish sits under a Louisiana Gulf climate: strong sun, high humidity, heavy rainfall during storm events, and the storm cycle that comes with a hurricane-prone region. A coating specified for a drier climate often disappoints here, so the chemistry weighs the climate as well as the substrate.

Rainfall and ponding on an east-bank roof

Heavy rainfall during storm events can push water onto a low-slope commercial roof faster than the drainage can clear it, leaving a ponding pattern that is read on the next survey. The ponding reading on the roof is the input to the chemistry decision, so acrylic is usually ruled out on a roof that ponds.

River Ridge is not on the lake, but the east-bank Jefferson drainage network is a flat system; the ponding question on a specific roof is a drainage question before it is a chemistry question.

Gulf sun and UV exposure

Louisiana sun is strong year-round, so ultraviolet exposure on a coating is higher than in cooler climates. A reflective finish on a draining field is one way to work with the UV load, but acrylic that reads well on a datasheet made in a cooler climate often ages faster here.

The chemistry and the mil thickness are specified for the sun exposure at the roof as well as for the ponding pattern.

Surveys sit ahead of coating specs

The commercial inspection page covers the moisture-survey methods that read the roof deck and insulation before a chemistry is specified. A coating over wet insulation seals a problem in rather than fixing it, which is why the survey leads.

A sound substrate is the condition under which any coating chemistry performs; the survey is where the condition is read.

Big Easy Roofing Process

Four steps. The failure mode picks the chemistry; the published standard sits next to the acrylic specification where acrylic is the fit; the parish office answers the permit question.

A roofer surveying a commercial roof before an elastomeric coating is specified on a Jefferson Parish building
01

01 Survey the roof

Substrate, standing water, UV exposure and foot traffic paths read on the roof, with the moisture reading taken on the deck and insulation where the walk raises the question.

02

02 Rank the three failure modes

Standing water, UV with reflectance loss, and foot traffic are ranked against each other on the specific roof; the leading one picks the chemistry.

03

03 Specify the chemistry and the published reference

Acrylic specifications cite ASTM D6083 as the common reference; silicone and polyurethane specifications cite the manufacturer datasheet. The datasheet governs for the specific job.

04

04 Route the parish office

Whether a commercial coating scope needs a parish permit is confirmed with the Jefferson Parish East Bank building permits office on (504) 736-6957; there is no city office in the sequence.

Everything else we do in River Ridge

The rest of the Big Easy Roofing services available in River Ridge, each with its own page and written scope. When a coating is not the right scope at all, the commercial roof coating page covers the four-scope decision that comes before chemistry.

Filter by service type:

River Ridge Commercial Elastomeric Coatings FAQs

Choosing the chemistry against the east-bank Jefferson envelope, how ASTM D6083 reads on an acrylic quote, and the parish office route.

Topic

Question not here?

Ask us about an elastomeric coating on a River Ridge commercial building. No charge and no obligation.

Call (504) 800-8196
Which elastomeric chemistry fits a River Ridge roof that ponds?

Silicone chemistry usually tolerates standing water better than acrylic, and acrylic is usually ruled out on a ponding roof. The product datasheet governs for a specific job.

What is ASTM D6083?

ASTM D6083 / D6083M is the published industry standard for liquid-applied acrylic roof coatings. It sets the material and performance requirements that let a specifier read two acrylic products against the same reference. Silicone and polyurethane are specified from the manufacturer datasheet.

Can a new elastomeric coating go over an old one?

Sometimes. Compatibility is checked first, because some chemistries do not bond to others, and the datasheet governs. A silicone over an acrylic, for example, often needs a specific primer or preparation that the datasheet calls out.

Which chemistry handles foot traffic?

Polyurethane chemistry is commonly chosen for traffic lanes where abrasion is the leading failure mode, or a separate walkway pad is specified alongside a different chemistry on the field.

Does a commercial elastomeric coating need a permit in River Ridge?

The Jefferson Parish East Bank building permits office on (504) 736-6957 confirms the permit question for the specific address and scope. River Ridge is unincorporated, so there is no city permits office in the sequence.

When is a coating the wrong answer on a commercial roof?

When the insulation is wet, when the ponding pattern is beyond the chemistry’s tolerance, or when the membrane is at the end of its useful life. The commercial roof coating page covers that four-scope decision before chemistry.

Will my insurance cover a commercial elastomeric coating?

That is a question for your insurer. Under R.S. 37:2159.1 a Louisiana roofing contractor may not interpret your insurance cover.

What does a commercial elastomeric coating cost?

It is priced on area, substrate and chemistry after the roof is surveyed and the ponding reading is taken, so the price follows a walk on the building.

Match the chemistry to the leading failure on a River Ridge commercial roof

A River Ridge commercial elastomeric scope opens with a walk on the substrate, ranks the three leading failure modes on the specific roof, specifies the chemistry with its published reference where one exists, and routes the permit question to the Jefferson Parish East Bank building permits office. There is no city office in the sequence. If you would rather start in writing, tell us what the job involves and we will come back with an estimate.

Call (504) 800-8196
Commercial Elastomeric Coatingsin River Ridge