Big Easy Roofing Logo
Claim Banner - Big Easy Roofing Big Easy Roofing roof replacement guarantee banner
Call Our Roofing Experts!(504) 800-8196
Home/Service Areas/Louisiana/River Ridge/Roof Flashing Repair

Roof Flashing Repair in River Ridge, LA

Big Easy Roofing repairs flashing across River Ridge and the east bank of Jefferson Parish. The scope names the one detail that is failing, checks whether a wide chimney has the cricket the code calls for, and photographs the metal before and after.

$350 to $1,500Estimated flashing repair
Over 30 inChimney width where a cricket is called for
Written scopeNames the detail
PhotographedBefore and after

River Ridge roof flashing repair at a glance

Flashing is the sheet metal or other material that sheds water where the roof covering meets something that breaks it, such as a chimney, a wall or a pipe. A River Ridge flashing repair names the detail that is most likely failing, and checks whether a wide chimney also needs the cricket the code calls for.

A specific detail, written down

Not "fix the flashing"

The scope names the detail: chimney step flashing, counter flashing, wall junction, pipe boot, vent collar or edge metal. A scope that does not name it is more likely to be a guess.

Crickets behind wide chimneys

Over 30 inches

The 2021 International Residential Code, section R903.2.2, calls for a cricket or saddle on the ridge side of a chimney or other penetration wider than 30 inches, measured perpendicular to the slope. A cricket turns water around the chimney instead of letting it pool.

Flashing at a reroof

Sections R908.5 and R908.6

The reroofing provisions of the same code have two sections to know: R908.5 on reinstalling existing materials, including flashing and edging, and R908.6 titled Flashings. We do not quote either; ask the parish how they apply to your job.

Metal first, sealant second

Where the metal is sound

If the metal is in good condition and only the sealant has failed, cleaning and re-sealing can be the right repair once it has been inspected. If the metal is corroded or bent, sealing over it only buys time.

A trace comes first

Usually

A leak trace points to which flashing is most likely letting water in, so the repair goes where the leak most likely is.

Your insurer decides cover

Not us

Louisiana R.S. 37:2159.1 bars a roofing contractor from acting as a public adjuster or interpreting insurance policy coverage. We write the scope and photograph the detail.

Every figure on this page is an estimate, not a quote, and is subject to Big Easy Roofing sign off. Cost and timescale depend on size, pitch, access, weather, materials and whatever is found once work starts, so call Big Easy Roofing on (504) 800-8196 and we will come out and give you an estimate for your own roof.

Every price on this page is an estimate, not a quote. Call Big Easy Roofing on (504) 800-8196 to look at a flashing on your River Ridge roof.

Which flashing is failing, and what the repair involves

Flashings are not interchangeable. The table lists the common cases, where each sits on the house and what each repair involves, so you can see which detail is being discussed, and what it is estimated at, before any work starts on your River Ridge roof.

FlashingWhere on the houseWhat the repair involvesEstimated
Chimney step and counter flashingWhere the chimney meets the roofOld step flashing cut out, new installed, counter flashing re-sealed or reset$500 to $1,500
Chimney cricketRidge side of a wide chimneyA saddle, usually sheet metal, built behind the chimney and flashed inScoped on site
Wall junction flashingWhere a roof meets a vertical wallNew flashing installed under the wall cladding or counter-flashed into masonry$350 to $1,200
Pipe boot or vent collarWhere a pipe passes throughOld boot cut off, new one installed and sealedScoped on site
Edge metal and drip edgeAt eaves and rakesRusted or damaged edge metal replacedScoped on site

Every price is an estimate and none of it is a quote. The headline band for a flashing repair is $350 to $1,500, and a chimney that needs a cricket is priced on its size.

What the code says about flashing and crickets

Two sections of the residential code are worth knowing on a River Ridge flashing job: the cricket rule for wide chimneys, and the reroofing sections on existing flashing. The 2021 code, with state amendments, is the statewide edition, and the parish says how it applies to a given address.

The code in force

2021 IRC, statewide

Louisiana adopted the 2021 International Residential Code, with state amendments, from 1 January 2023, which includes Jefferson Parish. Its chapter 9 covers roof assemblies.

Crickets and saddles

Section R903.2.2

A cricket or saddle goes on the ridge side of a chimney or penetration wider than 30 inches, measured perpendicular to the slope. Its covering is sheet metal or the same material as the roof covering.

Flashing at a reroof

Sections R908.5 and R908.6

R908.5 deals with reinstalling existing materials in a reroof, including flashing and edging, and R908.6 is the section titled Flashings. They are the sections to ask the parish about when flashing is part of a reroof.

What the parish decides

Whether a repair needs a permit

Whether a particular flashing scope needs a permit is for the Jefferson Parish Department of Building Permits, East Bank office, at (504) 736-6957. How the parish has treated repairs is set out on the repair page, and a full reroof is on the replacement page.

Why a missing cricket can keep a wide chimney leaking

Water running down the slope hits the uphill side of a wide chimney and pools there. Re-sealing that joint without a cricket can fail again in the next heavy rain.

We measure the chimney first. If it is 30 inches wide or less, that rule does not call for one, and we say so.

What we do not tell you

We do not say any particular chimney needs a cricket until we have measured it, and we do not say a flashing job is exempt from a permit. That is the parish’s call.

We write the scope specifically enough that the parish can answer.

Why flashing fails on a River Ridge house

Flashing tends to fail at the same few places, and for the same few reasons. Knowing them is how a repair lands on the right one, and why the scope reads the metal and the older repairs rather than only the sealant on top.

Heat and damp work on the sealant

A roof on the east bank of Jefferson Parish sees frequent heating, cooling and humidity. Sealant at a flashing moves with it and can lose its grip over the years, sometimes before the metal itself has failed.

That is why the scope reads the condition of the metal, not only the sealant above it.

Rain pushed sideways

In a storm, rain is driven against the back of a vent cap, the face of a chimney and the side of a dormer. Those are surfaces that get less direct rain in ordinary weather.

A flashing can read clean from one side and be failing on the other, so both sides are photographed.

Older repairs hide the real fault

A flashing that has been sealed over more than once can be a sign the leak was chased rather than found. Layers of sealant can hide a split or a gap in the metal beneath.

The scope may cut back to bare metal to see what is there before it decides between re-sealing and replacing.

Big Easy Roofing Process

Four steps. The flashing is photographed before anything is cut, so the scope and the finished work are tied to the same evidence.

A roofer inspecting chimney step flashing on a River Ridge residential roof
01

01 Find the failing detail

A leak trace points to the flashing most likely letting water in. The detail and the roof around it are photographed.

02

02 Measure and write the scope

The chimney width is measured for the cricket question, and the scope names the detail, the metal and the method.

03

03 Check the parish

A call to the Jefferson Parish East Bank Building Permits office on (504) 736-6957 checks whether the scope needs a permit for your address.

04

04 Cut, install and photograph

Old flashing cut out, new installed and sealed following the manufacturer instructions where they apply, and the finished detail photographed before the ladders come down.

Everything else we do in River Ridge

The rest of the Big Easy Roofing services available in River Ridge, each with its own page and written scope. A flashing repair usually follows a leak trace, which points to the likely entry point so the scope knows where to cut.

Filter by service type:

River Ridge Roof Flashing Repair FAQs

The questions worth asking before a flashing repair on a River Ridge roof.

Topic

Question not here?

Ask us anything about a flashing on your River Ridge roof. No charge to ask.

Call (504) 800-8196
Which flashings do you repair?

Chimney step and counter flashing, wall junction flashing, pipe boots, vent collars and edge metal at eaves and rakes. The scope names the specific detail.

Can you re-seal a flashing without cutting it out?

Sometimes. If the metal is sound and only the sealant has failed, cleaning and re-sealing can be the right work once it has been inspected. If the metal is corroded or bent, re-sealing it is a short term fix.

What is a chimney cricket?

A small ridge, usually sheet metal, built on the uphill side of a chimney that turns water around it instead of letting it pool. The 2021 International Residential Code, section R903.2.2, calls for one behind a chimney or penetration wider than 30 inches, measured perpendicular to the slope.

Does my chimney need a cricket?

Under that section, a cricket is called for when the chimney is wider than 30 inches measured perpendicular to the slope. We measure it before we say, because a chimney 30 inches wide or less is not covered by that rule.

What do the reroofing sections say about flashing?

In the 2021 International Residential Code, R908.5 deals with reinstalling existing materials in a reroof, including flashing and edging, and R908.6 is the section titled Flashings. We do not quote either. Ask the Jefferson Parish East Bank Building Permits office on (504) 736-6957 how they apply to your job.

What does flashing repair cost in River Ridge?

A flashing repair is estimated at $350 to $1,500, driven by the length of the run, access and whether the metal is sound. A chimney cricket is priced on its size. Every figure is an estimate.

Does a flashing repair need a parish permit?

That is for the Jefferson Parish East Bank Building Permits office to say for a River Ridge address, on (504) 736-6957.

Will you handle my insurance claim?

No. Louisiana R.S. 37:2159.1 bars a roofing contractor from acting as a public adjuster or interpreting insurance policy coverage. We write the scope and photograph the detail.

Name the detail, measure the chimney before any flashing is cut

A flashing scope that names the specific detail, measures the chimney for a cricket and photographs the metal before and after gives the repair the best chance of holding. If you would rather start in writing, tell us what the job involves and we will come back with an estimate.

Call (504) 800-8196
Roof Flashing Repairin River Ridge