Fascia Board Repair in Metairie, LA
Big Easy Roofing replaces rotten, damaged and paint failed fascia board across Metairie and unincorporated Jefferson Parish, licensed by the Louisiana State Licensing Board for Contractors. Most Metairie fascia repairs run $15 to $30 per linear foot installed and painted, and are usually caught during a gutter repair when the wood behind the gutter is exposed.
Metairie fascia board repair at a glance
A Metairie fascia board repair is a per linear foot job: measure the affected run, remove the rotten section, replace with primed pine, cedar or PVC trim board, and paint to match existing. Cost runs $15 to $30 per linear foot installed and painted. Most single elevation repairs are finished in one day, with the gutter re hung the same visit if it was pulled to access the fascia.
Estimated cost per lf
Wood or PVC fascia board, installed and painted to match, on a Metairie residential home. Priced per linear foot of affected run.
Typical section repair
Single elevation fascia repair on 15 to 25 linear feet, including gutter removal and re hang if needed.
Permit authority
Fascia repair is a trim board replacement, not construction, so no Jefferson Parish permit is required.
Materials offered
Primed pine (cheapest), cedar (rot resistant, mid), PVC trim board (never rots, most expensive). PVC is the durable choice on a Gulf Coast home.
Typical timeline
Most single elevation fascia repairs are completed on a single visit, with the gutter re hung the same day.
Warranty
One year workmanship warranty on every fascia repair, covering the install and the paint finish.
Every figure on this page is an estimate, not a quote, and is subject to Big Easy Roofing sign off. Cost and timescale depend on size, pitch, access, weather, materials and whatever is found once work starts, so call Big Easy Roofing on (504) 800-8196 and we will come out and give you an estimate for your own roof.
Fascia board is the horizontal wood trim board that runs along the eave and carries the gutter. On a Metairie home it is the first exterior wood to fail because it sits behind the gutter, holds water any time the gutter overflows, and rots from the back where nobody sees it. The tell is usually visible only when the gutter starts to sag, because the fascia has softened enough that the hangers pull out.
Fascia repair replaces the affected section, primes and paints to match, and re hangs the gutter behind the drip edge as it was. Where the rot is more than 30 percent of one elevation, the whole run is replaced rather than patched. On a Gulf Coast home a switch from wood to PVC trim board at the repair stage eliminates the problem for the life of the house.
Per linear foot cost is for a Metairie residential fascia repair including gutter removal and re hang, primed and painted to match existing trim. Volume discounts apply on multi elevation repairs.
Metairie fascia repair options and material choice
Five fascia scopes cover most Metairie repairs, and the material choice usually settles between primed pine (cheapest), cedar (rot resistant), and PVC trim board (permanent). On a Gulf Coast home PVC is the honest recommendation for any repair the homeowner does not want to redo in 10 to 15 years.
| Repair scope | What we do | Estimated cost | Life expectancy |
|---|---|---|---|
| Small section, primed pine | Cut out rotten section, install primed pine, paint to match | $15 to $20 per lf | 10 to 15 years |
| Small section, cedar | Cut out rotten section, install cedar, prime and paint to match | $20 to $25 per lf | 15 to 25 years |
| Small section, PVC trim | Cut out rotten section, install PVC trim board, prime and paint | $25 to $30 per lf | Lifetime of house |
| Whole elevation replacement | Replace entire fascia run on one elevation, gutter re hung | $400 to $1,200 | Material dependent |
| Multi elevation replacement | Replace fascia on two or more elevations, gutter re hung all round | $1,200 to $3,500 | Material dependent |
| Fascia + gutter combined | New fascia + new seamless aluminum gutter on same visit | $20 to $40 per lf | Full system reset |
Estimated market ranges only. Call (504) 800-8196 for a written estimate on your Metairie fascia repair.
Permits, insurance and material choice on a Metairie fascia repair
A Metairie fascia board repair does not trigger a Jefferson Parish permit because trim board replacement is not roof covering work. Most fascia repairs price under the Louisiana licence threshold of $7,500. Whether insurance pays is a question for your insurer, and what we document is the physical cause, since sudden storm or impact damage looks nothing like long term rot from gutter overflow.
Fascia repair itself
Replacing trim board on a Metairie home is not a roof covering change, so Jefferson Parish issues no permit and charges no fee for a fascia repair visit. The parish permit rule applies only to covering replacement work.
PVC vs wood decision
PVC trim board costs 50 to 100 percent more than primed pine per linear foot but never rots. On a Gulf Coast home the PVC pays back within one repair cycle. Big Easy Roofing prices both options in the scope so the choice is a real one.
Storm damage and insurance
Coverage is your insurer's decision and Louisiana law does not allow a contractor to interpret it. What Big Easy Roofing does is establish and photograph the physical cause, because sudden storm or impact damage and long term rot from gutter overflow are readily distinguishable on site, and write a good faith itemised estimate.
Fascia repair with re roof
A full re roof is the best time to replace fascia because the drip edge and gutter come off anyway. Big Easy Roofing prices fascia replacement as a line item on any Metairie re roof scope where the wood is failing, and the extra cost is small relative to a separate visit later.
Why PVC trim beats wood on the Gulf Coast
PVC trim board (AZEK, Kleer, Versatex) never rots, never absorbs water, never carpenter bee bores into it, and holds paint 15+ years without peeling. Wood fascia on a Metairie home typically fails every 10 to 15 years even on cedar because Gulf humidity keeps it damp.
The upcharge from primed pine to PVC is small ($5 to $10 per linear foot). Over the life of the house it pays back within one repair cycle avoided.
Fix the cause, not just the fascia
Fascia rot on a Metairie home is almost always caused by gutter overflow, which is almost always caused by a blocked downspout or a sagging gutter. Replacing the fascia without fixing the gutter behind it is a temporary fix, and the new wood rots in the same spot within a few years.
Big Easy Roofing bundles a Metairie gutter repair with the fascia scope so the cause and effect are addressed together.
Why Metairie fascia rots first
Three failure patterns dominate the Metairie fascia repairs Big Easy Roofing does. Gutter overflow saturates the fascia from behind, carpenter bees bore into unpainted end grain, and paint fails on the south facing eave under UV load. Each has its own tell and its own permanent fix.
Gutter overflow saturating fascia from behind
A blocked or sagging gutter overflows behind the fascia rather than over the front edge. Water then sheets down the back side of the fascia board where the paint does not seal, saturates the wood, and starts rot from behind. By the time the front of the fascia looks damaged, the back is already soft.
The fix is fixing the gutter first, then repairing or replacing the fascia. Big Easy Roofing bundles both on the same visit.
Carpenter bees boring into end grain
Carpenter bees drill perfectly round half inch holes into unpainted or weathered wood end grain, and Metairie fascia end caps are a favourite target. A single bee gallery reduces structural wood section significantly, and a colony of bees can undermine an entire fascia run.
PVC trim board is immune. On repair with wood, priming and painting every cut end, including the ones tucked behind the gutter, is what deters the next generation of bees.
South facing paint failure under UV
South facing Metairie eaves take the worst UV load, and cheap exterior paint fails there first. Peeling paint exposes the wood, which then absorbs moisture and rots. The tell is a distinct paint band on the south fascia that has weathered while the north side still looks fresh.
Repaint with a high quality acrylic exterior paint (Sherwin Williams Duration, Benjamin Moore Aura) buys 10 to 15 years. A switch to PVC trim board eliminates paint failure entirely.
Big Easy Roofing Fascia Repair Process
Three steps from the first call to a finished fascia repair: free on site diagnosis of every affected linear foot, written per foot quote with the material choice priced out, and a same day repair with the gutter re hung and the paint matched. Call (504) 800-8196 to book the visit.
Free fascia diagnosis
Same week visit at the address. The estimator measures every affected linear foot, probes for rot behind the gutter, and photographs the damage. The scope is written up per elevation so the homeowner sees exactly what is being repaired.
Written quote with material choice
The scope prices primed pine, cedar and PVC trim board side by side so the material decision is a real one. Gutter removal and re hang is included in the price, as is paint match to the existing trim colour.
Repair completed in one day
Most Metairie fascia repairs are finished on a single visit. Rotten section removed, new fascia board cut and installed, primed and painted to match, gutter re hung. Workmanship warranty is filed with the invoice.
Everything else we do in Metairie
The rest of the Big Easy Roofing services available in Metairie, each with its own page, crew and written scope. Because the fascia and the soffit form one eave assembly, a Metairie soffit installation is often priced on the same visit while the eave is already open.

Roof Replacement in Metairie
Read More
Roof Repairs in Metairie
Read More
Roof Inspection in Metairie
Read More
Hail Damage Roof Repair in Metairie
Read More
Storm Damage Roof Repair in Metairie
Read More
Storm Damage Emergency Response in Metairie
Read More
Emergency Roofing in Metairie
Read More
Roof Leak Detection in Metairie
Read More
Roof Maintenance in Metairie
Read More
Roof Coating in Metairie
Read More
Roof Ventilation in Metairie
Read More
Roof Weatherproofing in Metairie
Read More
Roof Restoration in Metairie
Read More
Roof Flashing Repair in Metairie
Read More
Gutters and Downspouts Installation in Metairie
Read More
Gutters and Downspouts Repair in Metairie
Read More
Siding Installation in Metairie
Read More
Asbestos Roof Removal in Metairie
Read More
Roof Insurance Claims in Metairie
Read More
Soffit Installation in Metairie
Read More
Soffit Repair in Metairie
Read More
Commercial Roof Replacement in Metairie
Read More
Commercial Roof Repairs in Metairie
Read More
Commercial Roof Inspections in Metairie
Read More
Commercial Hail Damage Repair in Metairie
Read More
Commercial Re-Roofing in Metairie
Read More
Commercial Roof Coating in Metairie
Read More
Commercial Elastomeric Coatings in Metairie
Read More
Commercial Roof Ventilation in Metairie
Read More
Commercial Roof Leak Detection in Metairie
Read More
Commercial Siding Installation in Metairie
Read MoreMetairie Fascia Board Repair FAQs
The questions Metairie homeowners actually ask us about fascia board repair, answered before you have to pick up the phone.
Topic
Question not here?
Ask us anything about your Metairie fascia and eave trim. We usually answer the same day, no charge and no obligation.
Call (504) 800-8196How much does fascia board repair cost in Metairie
Estimated ranges. Metairie fascia repair runs $15 to $30 per linear foot installed and painted. Primed pine sits at $15 to $20. Cedar at $20 to $25. PVC trim board at $25 to $30. A typical single elevation repair on 15 to 25 linear feet runs $300 to $700 including gutter re hang.
Wood or PVC fascia for a Metairie home
PVC on a Gulf Coast home. PVC trim board (AZEK, Kleer, Versatex) never rots, never absorbs water, never carpenter bee bores into it, and holds paint 15+ years. Wood fascia on a Metairie home typically fails every 10 to 15 years even on cedar because Gulf humidity keeps it damp. The upcharge from primed pine to PVC pays back within one repair cycle avoided.
How do I know if my fascia needs repair
Four tells. A sagging or pulled gutter is often the first sign that fascia has softened behind it. Peeling or blistering paint on the fascia surface. Round half inch holes drilled by carpenter bees. Visible dark stains where water has run behind the gutter. Big Easy Roofing probes for rot on the free visit before writing the scope.
Do I need a Jefferson Parish permit for fascia repair
No. Fascia board replacement is a trim board repair, not roof covering work, so Jefferson Parish does not require a permit. The parish permit rule applies only to roof covering replacement at or above 50 percent, which a fascia repair never crosses.
Will you match the paint color to my existing trim
Yes. Big Easy Roofing colour matches the existing trim from a paint chip or a sample cut, and paints the new fascia on site or in the shop before install. Sherwin Williams Duration and Benjamin Moore Aura are the standard exterior finishes used. Paint match is included in the per foot price.
How long does a Metairie fascia repair take
Most single elevation fascia repairs are finished in one day, including gutter removal, rot cut out, new fascia install, prime, paint and gutter re hang. Multi elevation repairs or a whole home replacement can take two to three days depending on total linear footage.
Does homeowners insurance cover a fascia repair in Louisiana
Whether a particular loss is covered is decided by your insurer, and La. R.S. 37:2159.1 prohibits a Louisiana contractor from interpreting policy coverage, so we will not tell you what your policy pays. What we can tell you is what caused the damage, which matters because sudden storm or impact damage and long term rot from gutter overflow are physically different things. Big Easy Roofing photographs the damage and writes a good faith itemised estimate you can hand to your insurer.
Do I have to fix the gutter to fix the fascia
Effectively yes. Fascia rot on a Metairie home is almost always caused by gutter overflow, which is almost always caused by a blocked downspout or sagging gutter. Replacing the fascia without fixing the gutter is a temporary fix, and the new wood rots in the same spot within a few years. Big Easy Roofing bundles both scopes.
Can carpenter bee damage be repaired without full replacement
Sometimes. A single or a few bee holes in otherwise sound wood can be filled with epoxy and repainted. A colony of bees or extensive galleries mean the wood section is compromised and the run needs replacing. PVC trim board on the replacement eliminates the problem for the life of the house because bees do not bore into PVC.
Do you repair fascia in Old Metairie, Bucktown and the lakeside neighbourhoods
Yes. Big Easy Roofing does fascia repair across all of Metairie, including Old Metairie, Bucktown, the Lake Vista side, and the neighbourhoods along Veterans and Metairie Road. Coverage extends to Kenner, Harahan, River Ridge and the rest of unincorporated Jefferson Parish. Historic Old Metairie homes often justify cedar or PVC over primed pine on aesthetic grounds.
Book a Metairie fascia repair inspection
Free on site fascia diagnosis, written per foot quote with primed pine, cedar and PVC priced side by side, and a same day repair with paint matched to existing trim.
Call (504) 800-8196





